Menu
What's new
By:
Filters Better Search

Recent content by Mark the Red

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. M

    TP-Link EAP225v3 AC1350 Wireless MU-MIMO Gigabit Ceiling Mount Access Point Reviewed

    Not to necro a month old thread. I inherited a Edgerouter ER-4 from a buddy and I am finally taking the plunge into using dedicated access points with the router over my current AC-68u all in one router solution. My question is: Can the Asus AC-68u work just as well as the TP-Link...
  2. M

    Which NAS do you own?

    I have a Freenas 9 Server: Lenovo TS140 i3-4130 (Server Grade MB, ECC Support, Intel LAN, FSP PSU) ($200) 16 Gb ECC Ram ($150) 3x3TB WD Green with wdidle3.exe set to 300s ($300) 8GB Cruzer Fit Drive ($10) Display Port Cable ($10) For $700 its a killer server. Quiet, efficient and powerful...
  3. M

    rt-n66u settings for plex server (pms)

    I did. It says "Disconnect the server failed" when I click the manual port forwarding..... Do my settings look right with a port mapped to 26403? Does that need to be entered into the local port of my router port forward table?
  4. M

    rt-n66u settings for plex server (pms)

    However, when I go to myplex webpage the address is: I'm dumber than a bag of hammers with ports and just want this to work outside my local network.
  5. M

    rt-n66u settings for plex server (pms)

    Does this look right? My plex server is mapped to and it will NOT let me manually configure it to 32400.
  6. M

    rt-n66u settings for plex server (pms)

    I was on 46 I believe. To be honest I do not remember. I usually update around once a month. I always reset to factory defaults after flashing. I gather from your post that the default settings should be fine? Or that the router is not the problem here?
  7. M

    rt-n66u settings for plex server (pms)

    i cannot access my plex server from outside my local network. currently on 378.51 firmware and everything works great otherwise. i have a FreeNAS server running plex as my server connected to the rt-n66u. all my server settings are set to the plex server settings from the plex faq /...
  8. M

    RT-N66U + New FREENAS Server = Recommended Settings

    Long time lover of Merlin's work, but seldom post. Will be installing a new beefy FreeNas server this weekend using a very cheaply acquired TS140 server from Lenovo (i3+c226+ Intec NIC+ 16gb ECC Ram). Aside from enabling jumbo frames, is there any other settings that you recommend I engage...
  9. M

    Asuswrt-Merlin 376.45 is out

    Downloaded and installed. Like the new interface. Noticed no change on the wifi but is still incredible. ALMOST willing to install the printer into the USB port again. ALMOST. I still have nightmares from last time.....
  10. M

    Asuswrt-Merlin 3.0.0.4.372.30_2

    I'm getting constant USB HDD (.ext3 format) dropouts with this new firmware whenever i stream something via DLNA. Reformatting has not resolved this? Anybody else having issues? Nothing wireless related...everything is LAN connected.
  11. M

    Asuswrt-Merlin 3.0.0.4.372.30_2

    Just upgraded from my 266.24 firmware to this one. Works great for me and my family! Thanks for all your hard work.
  12. M

    Tomato by Shibby [RELEASE] 110 out now

    Can you check if it has gigabit ethernet speeds? That was what was preventing me from installing it before. Want to see if it resolves the Sony Mkv DLNA issue. Apparently the miniDLNA 1.0.26 does, but I have yet to try it. This mini dlna issue is what prevents me from updating my Asus...
  13. M

    Service Life?

    Google did a HUGE study of hard drive failures in their farms over time. It turns out there was very little correlation between operating temperature and fail rate. (corrected for obvious outliers such as drives catching fire due to faulty bearings, etc.) The biggest indicator of fail rate...
  14. M

    Changing wireless power setting

    Here is a thread on the subject by super router programmer Toastman: http://www.linksysinfo.org/index.php?threads/tomato-signal-strength-low-any-ideas.33868/ In brief, the US country regulation is a boolean variable that cancels out any and all modifications of the transmit power you make...
  15. M

    Compiling your own firmware - Possible for a non-computer science professional??

    Thanks all. I'll guess have to just bribe either Merlin or TeHashX with paypal donations or sexual favors to include this sony dlna fix on future firmware releases.
See more
Top