Menu
What's new
By:
Filters Better Search

Recent content by airwoflsnb

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. A

    RT-AC87U guest networking using separate subnets and vlans to trunk to another device

    @sfx2000 - yes, had come to that conclusion that some closed source sorcery is going on wrt Quantenna. For my setup, the primary doesn't cover the outside patio / deck or the den so when we have guests over they can't get wifi unless they are on the private SSID. I did move the VLAN...
  2. A

    RT-AC87U guest networking using separate subnets and vlans to trunk to another device

    See your point on the managed switch, and it is a good one. But part of the problem is that I can't get the separate bridges (or subnets) for guest vs private working, let alone testing the vlans.
  3. A

    guest-wifi (wl0.1) on a newly created bridge (br1), clients can't connect

    vlan10 didn't work. Am giving up on these devices to make it work for me. I think the Broadcom / Quantenna combination of using one physical interface is part of the issue. Think I am going to bite the bullet and write off the money I spent on these and get a couple of TP-Link AC2600s that have...
  4. A

    RT-AC87U guest networking using separate subnets and vlans to trunk to another device

    About had enough of this frustrating exercise. Couldn't get this working in Router mode so am going to try doing this in AP only mode and hard coding the default gateway. And another thing, after I make the manual VLAN changes, I can't save or perform any action in the UI - it simply redirects...
  5. A

    RT-AC87U guest networking using separate subnets and vlans to trunk to another device

    Have been reading that using vlan numbers <=5 might cause problems as they could be reserved for different things. Am going to try this again but using vlan10. Alternatively, there is another post I have found that talks about a need to update some nvram settings and restart eapd when you make...
  6. A

    guest-wifi (wl0.1) on a newly created bridge (br1), clients can't connect

    I have read that vlans below 5 might cause conflicting issues so am going to give say vlan10 a go.
  7. A

    guest-wifi (wl0.1) on a newly created bridge (br1), clients can't connect

    Sorry to hear. Assume you are running a later or latest version given the auth issue is solved in later versions? Because I can get auth working, but accesses the wrong bridge. Will give the nvram settings a go for my problem. P.
  8. A

    guest-wifi (wl0.1) on a newly created bridge (br1), clients can't connect

    Interestingly enough, I have a question here about guest network and separate bridge, where clients can connect but actually end up being connected to br0 despite wl0.1 being in br1 which confuses me terribly. Have a look at the commands I run and see if you get the same results as me?
  9. A

    RT-AC87U guest networking using separate subnets and vlans to trunk to another device

    Here are the outputs from the command line: $ robocfg show Switch: enabled Port 0: DOWN enabled stp: none vlan: 2 jumbo: on mac: 00:00:00:00:00:00 Port 1: 1000FD enabled stp: none vlan: 1 jumbo: on mac: 04:18:29:36:23:4a Port 2: DOWN enabled stp: none vlan: 1 jumbo: on mac: 00:00:00:00:00:00...
  10. A

    RT-AC87U guest networking using separate subnets and vlans to trunk to another device

    Hi, I have a frustrating problem I am trying to solve with a couple of Asus RT-AC87U's. Rather than explain my desired network setup, please find the diagram below - a picture equals a thousand words :) They are running Asuswrt-Merlin 3.80.59 Internet | +----------+ | ISP MOCA | |...
See more
Top