Recent content by alby258

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. A

    DNSCrypt Necessary or not?

    Same here, Dnscrypt is working like a charm with 384.7_2 firmware
  2. A

    Asus Merlin - Share VPN tunnel

    I'm in the same situation, but I only can make work the diagram that you wrote in example B (with the scripts linked on post #2). Can I ask you how did you do to make LAN devices reachables from Mobile(OpenVPN) like in the diagram A? I cannot manage it to work...
  3. A

    Step by Step: SNORT on AsusMerlin

    Installed on AC68U with NG-Entware. Everything is working well, average CPU usage around 5-10%, ram around 85-90%
  4. A

    Load Balanced Dual WAN - Routing Rules

    I use this code, similar to VPN routing. It works for me. #!/bin/sh sleep 2 touch /tmp/000wanstarted for i in /proc/sys/net/ipv4/conf/*/rp_filter ; do echo 0 > $i done # Delete and table 100 and flush any existing rules if they exist. ip route flush table 100 ip route del default...
  5. A

    Load Balanced Dual WAN - Routing Rules

    Nobody can help us? :p
  6. A

    Load Balanced Dual WAN - Routing Rules

    Same issue here. I have a secondary wan for only one device in my network and I want to reserve the connection only for it. Is there a way to do it?
  7. A

    RT-AC68U speed issue

    Same situation here with ReadyNas. I have a Pc with SSD and I use link aggregation between router and NAS, but I hit 100% on cpu usage on AC68U when transferring files at 50 Mb/s speed, on a wired gigabit lan between PC and router. I've NAT acceleration ON. Only on one time I hit 75 Mb/s...
  8. A

    Asuswrt-Merlin 378.50 is out

    I wonder why it doesn't work, because I don't use any VPN. Maybe it's an Asus secret.... :( So, Asus, if you hear me, make Bandwidth monitor and Traffic analyzer working fine! :rolleyes:
  9. A

    Asuswrt-Merlin 378.50 is out

    The JFFS2 partition is enabled and Apps Analysis is also enabled. Traffic analyzer for example works well. If it helps, in Traffic analyzer tab, per app visualization also shows only general traffic.
  10. A

    Asuswrt-Merlin 378.50 is out

    I've installed 378.50_ta after 378.50beta2. On Bandwitch monitor of Adaptive QoS per app analysis doesn't work properly even after some days. It shows only "general" traffic. On beta2 it worked perfectly. Anyone with this problem? I've an AC68U and I did a factory reset before betas.
  11. A

    [CLOSED] Asuswrt-Merlin 378.50 Beta 1 is out

    I have noticed a problem with nat acceleration on: when is on, I can't reach my nas web interface and smb from wifi, but works well on ethernet. Surprised me that I can reach the web interface from wifi only using my asus ddns address. With nat acceleration off I can reach the web interface and...
  12. A

    Asuswrt-Merlin 376.47 and DropBop really slooooooow

    The same problem also here. Dropbox client in AiCloud 2.0 starts sync but after some minutes it stops. If you restart the process it hangs in "initial" state.
  13. A

    Broken traffic monitor?

    Here is my run: 0 eth0 usb eth0
  14. A

    Asuswrt-Merlin 3.0.0.4.374.33 Beta 3 available

    I have your same problem with AiCloud. I can access to the AiCloud interface but when I click on my attached USB drives I get an error. I get the error message from my pc and also from my android app. With windows I can normally access to my files on attached drives. With beta1 firmware all...
  15. A

    aicloud problem

    I had a similar problem updating to the last firmware. I solved saving my router setup on my pc, then I restored factory setting on the router and finally I loaded my config file back to it. After reboot aicloud started to run again. Hope this will help you. :)
Top