Recent content by bmb

Its OK, no real inconvenience to me, I didn't wish to take up any more of your time for what may be little gain to the community. Over the weekend I'll do as you suggest and see if you can spot anything of interest.

Following the factory reset, initialize, running v1.25 crashes the router almost straight away. Then after reboot I ran v1.24 and thought all was well, but after several mins (about 5mins), crashed again. I didn't know it was crashing before due to the longish delay after running the script...

I think the first crash may have been with v1.24 but wasn't so obvious because I'm simply running this router as a test for USB WAN. So before making any more changes let me do a factory reset and start again

I had already replaced the script with v1.25, (do I need to go back back to v.24 first?), so then ran these codes and it crashed and rebooted again. admins@RT-AC87U-6798:/jffs/scripts# ./vlanswitch.sh 20 del (vlanswitch.sh): 24132 v1.25 non-Public Beta ? 2016-2018 Martineau. VLAN configuration...

Apologies I did the above before I saw your last post...I'll do as you suggested

I update to script v1.25 ran these commands and the router crashed and rebooted admins@RT-AC87U-6798:/jffs/scripts# ./vlanswitch.sh 20 2 autodnsmasq (vlanswitch.sh): 2473 v1.25 non-Public Beta ? 2016-2018 Martineau. VLAN configuration utility...

I'm not sure if its me or not, it could well be, though when I run that command again now I get this: admins@RT-AC87U-6798:/jffs/scripts# ./vlanswitch.sh 20 status verbose ***ERROR Cannot display status; VLAN 20 (or Bridge br20) not found admins@RT-AC87U-6798:/jffs/scripts# No...

I've had a chance to run those commands, though without a VLAN device connected. I think I need to reconfigure the switch first as the main router I'm using has the main subnet and VLAN through one port, the RT87 splits them So I'll come back to testing with devices connected another time when I...

Here is the output... admins@RT-AC87U-6798:/jffs/scripts# ./vlanswitch.sh 20 status verbose ***ERROR Cannot display status; VLAN 20 (or Bridge br20) not found admins@RT-AC87U-6798:/jffs/scripts# Any further tests I can try?

Thank you, I do try to problem solve using the supplied help. Yours is indeed very comprehensive and covered the errors I saw I will do, though I'll have to wait until I can temporarily move them over from the ER4, others in the house are connected and don't want to interrupt them. I'll get...

Thank you, script is now running. admins@RT-AC87U-6798:/jffs/scripts# ./vlanswitch.sh 20 (vlanswitch.sh): 26430 ***ERROR VLAN (vlan20) via Switch Port 5 not defined in '/etc/ dnsmasq.conf' - (use 'autodnsmasq' directive) So went ahead with...

I'm probably making a fundamental mistake, so to let you know what I did. I downloaded the script, renamed it vlanswitch.sh and placed it into /jffs/scripts. Rebooted. Then: admins@RT-AC87U-6798:/jffs/scripts# l -rwxr-xr-x 1 admins root 73 Nov 28 13:42 dnsmasq.postconf*...

Thank you, I'll try it and let you know. I'd put my 87U into mothballs, but wanting to use it as a test bed/backup. WAN will be via USB, now that I've got an unlimited 4G DATA plan I'm thinking of ditching my fixed line broadband if it proves to be reliable.

@Martineau I have an AC87U and if its supported would like to try your script. I have a managed switch and looking to create one VLAN on port 2, just ethernet, no VPN or WLAN, WiFi is turned off on this router.

That's good news, thank you. I think those of us that have come to know pixelserv-tls and yourself from this forum have better understanding of it and the use of the client certificate, users on other forums seem nervous about it. The brief discussions about it on the relevant UBNT boards...