Recent content by bortek

I ended up with this config (merlin on primary and stock on mesh nodes) which has been working since my previous post. Didn't need to do any reset of primary. Just flashed mesh nodes with stock and re-added them. Primary Current Version : 3004.388.8_4 Manual firmware update : Upload Mesh...

Yes I will be switching to stock in both primary and secondary. Will do it in 2 weeks. Let you know how it goes.

Tested now adding another AC86U-Pro (same FW as primary) as a secondary node and guess what? Exactly the same issue. I though Merin was rock solid and stable FW. Now going back to stock will require reset and reconfigure the whole worlds from scratch. Doh...

I am waiting with upgrading fw on primary node. So far I have tested both latest merlin and stock FW on two AC86U units, connceted them as secondary but both behave in similar way. Doing factory reset then search and add as secondary node. Node added OK. Then after 2 mins it gets disconnected...

Hi I have AX86U-Prod as a main/primary router. Is it running asuswrt merlin 3004.388.8_4. Have added AC86U unit as a secondary AiMesn node but it dissapears after primary is rebooted. Not sure which firmware it is running but it one of 386.* it is. Is there any compatibility issues with that...

On my AX86U-Pro there is no such setting for Geoforce. I ended up adding this script and manually stopping the service /jffs/scripts/nat-start (dont forget to chmod +x) Why nat-start and not some other scripts? Because all other script execute before miniupnp service is started. nat-start...

Now I have looked and there are versions numbers for certs and 2 Root certs which are trusted. I connected a phone to get a "Trust" pop-up, trusted then went and looked again in About but there was not any cert that I could trust.

Hi I am trying to setup iPhone 15 as a USB tethering modem on AC86U using latest AsusWRT-Merlin fw. All works well, except that I need to manually press Trust popup every time I reconnect phone or most importantly every time I reboot the router. Idea was to use iPhone as a 5G modem and if I...

a short update. I replaced the SIM card (of the same mobile operator) that was sitting in USB/4G doungle and was connected to the router. So I blame the mobile operator doing something with the traffic. This can come back though e.g. if they detect usage of the VPN and they want to...

The damm thing started to work by itself without me doing anything. I blamed mobile operator was doing some magic with the traffic.

I think I wasn't clear enough about a SIM. After I replaced it I stayed atvthe Site-KL dor a few days and was using Internet with that SIM and it worked just fine. So the sim itself is working. And also checked with mobile operator and they are not blocking any sort of vpns. An yes I am using...

There is something weird going on with one of my VPN tunnels. I Have a setup according to this drawing which has been working up until now. First Short description of the setup. It is Site-to-Site OpenVPN where Site-JS is a server and two on the left/right are clients. VPN tunnel towards...

I am running Merlin and had scripts enabled in the GUI Permission are just like yours I am too a vi geek, never use nano unless forced :) Recopied the contents in notepadd++ to remove all the crap chars. Added # to empty lines (just in case) and made sure no tabs are present. Re-pasted into a...

Hi My apologies for a very very late response. All of your suggestions worked out very well and it worked as I wanted it. Now of course one wants these rules to be persisted across router reboots. What I have tried is this startup script according to the instructions I found. I placed it in...

I have tried to add these rules for these 2 hosts to be able to talk to each other. So far no success. 192.168.102.57 is my host on 5Ghz guest net which has wl1.1 interface and should also be using br2 interface for bridging 192.168.2.194 is another host on LAN (and br0) iptables -I FORWARD...