Recent content by cailloux

OpenSSL scheduled a release (1.0.2d) for Thursday that fixes a high severity issue. It's probably worth including the updated release instead of 1.0.2c.

I experienced the same issue with the bootloader not upgrading on my AC68u (currently v1.0.1.1). I think this is the relevant snippet from the syslog that shows the CFE upgrade attempt, to the extent it is helpful to figure out why it doesn't upgrade as expected. Nov 30 19:00:21 kernel...

Try turning 2.4Ghz bandwidth from 20/40MHz to 20MHz. I believe 20/40 is the default. I had similar issues and this resolved it immediately. I'd also suggest turning of beamforming (Wireless -> Professional) on both 2.4GHz and 5GHz. You'll need to turn off two beamforming options per page.

It was working great until ~48 hours after I installed .42 (AC-68R). Then wifi throughput would slowly drop to zero on multiple devices. 2.4G and 5G were already locked to a single band. I disabled beamforming with no change. Then I reduced 2.4G bandwidth to 20MHz (from 20/40MHz) and all...

Why wouldn't you connect all devices to the 24-port switch, versus having the NAS connected to the switch in the AC66 and then in to the 24-port switch? The switch may be trying to apply some sort of Spanning Tree and shutting the port down to prevent (what it thinks are) loops. I assume that...

I noticed that the only time I'm automatically logged out of the web GUI on 41 Beta 2 is when I have the web interface open in a tab/window for 30 minutes (per Admin/System settings, browser is Chrome). Any time I close the tab before 30 minutes elapses, I can access the web interface without...

Results after ~12 hours (where I would have previously seen the overflow message in the syslog): admin@RT-AC68R:/# ip6tables -t mangle -L -v Chain PREROUTING (policy ACCEPT 80529 packets, 9823K bytes) pkts bytes target prot opt in out source destination 137K...

I spoke too soon. I'm getting the neighbour table overflow message in the syslog. admin@RT-AC68R:/# ip6tables -t mangle -L -v Chain PREROUTING (policy ACCEPT 45624 packets, 4136K bytes) pkts bytes target prot opt in out source destination Chain INPUT (policy...

It was removed, to improve the security of the router. If you need command line access, use SSH. Per the release notes: - REMOVED: Removed the Run Cmd page as it was a security risk. This is also needed to keep in line with recent security fixes Asus...

I'm seeing the expected behavior, which is to say no error messages are showing up in my syslog (Comcast, IPv6). I don't know if an "I haven't seen the issue" response is helpful. My output: admin@RT-AC68R:/# ip6tables -t mangle -L -v Chain PREROUTING (policy ACCEPT 94 packets, 8919...

I manually specified the channel numbers on 2.4 and 5GHz bands. I left bandwidth at 20/40MHz (2.4GHz) and 20/40/80MHz (5GHz). It's back to the rock solid performance I experienced with earlier builds. I'm holding off on 374.40 until there's a stable Merlin build. I read in another post...

I think manually setting the channel did it. Thanks! I also set the Preamble to Short, and noticed no perceptible change.

I'm not restoring from backup. My process was: 1) Install firmware. 2) Factory Reset. 3) Configure settings (SSID, DHCP, DNS, NTP). I just set the channels manually on both bands. I hope it's that simple.

My AC68 wifi seems to go down every ~10 minutes running 374.40 Alpha 4. I regain access to the network on my laptop by turning off and then on the wifi switch or turning off/on Airplane mode on Android and iOS. I had no issues on 374.39. I flashed 374.40 Beta 3 and factory reset it when I...

Except Amazon Route 53. Which is feedback I've given several times to OpenDNS (DNS-O-Matic). That's the one thing I can point to today to say my setup is "less than perfect."