What's new
By:

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by clvk07

  1. C

    3006.102.3 WIFI TX power bug

    BE88U running 3006.102.3 with one AI mesh AX86uPRO. Changed the TX power to both 2.4 and 5 to balance and all clients started to lose wifi connection, even clients just beside the router or mesh. rebooted both few times no joy. WIFI started to working again after reboot and then gone again...
  2. C

    3006.102.3 and AIMESH

    Yes did set the aimesh to default and also upgraded the firmware to the latest stock
  3. C

    3006.102.3 and AIMESH

    updated the BE88U to the latest merlin 3006.102.3 from 3006.102.2 and having issues with the only AIMESH node AX86UPRO on stock 3.0.0.6_102_34336. Initially it wouldnt find the node, and now shows weak signal backhaul connection. Is there any known issue or fix to this?
  4. C

    Looking for feedback: Anyone considering AiCloud important to them?

    Only feature i used was the sync server to dropbox is it gone with 3006?
  5. C

    connmon Common and BE88U

    Hi Seems using BE88U with merlin 3006.102.2 common doesnt hold the settings. It saves them and then if you get to another page and come back settings are gone. Tried chrome/edge and reinstalled. Only Skynet and Common Installed. Any ideas?
  6. C

    Device to AIMESH Nodes Connection

    yes did that , There are about 9 meters from each other and one is upstairs Currently have set up as -85
  7. C

    Device to AIMESH Nodes Connection

    Ye using as wireless backhaul. I did on both 2.4 and 5 GHZ at the time but little result
  8. C

    Device to AIMESH Nodes Connection

    Played with those settings before, don't think I got very far... Is that the only setting?
  9. C

    Device to AIMESH Nodes Connection

    Hi Using AX86U and TUX3000 V2 as mesh. FW version 388.7. Seems that when I move upstairs the devices still stay connected to the node downstairs with low signal (1bar) if I disconnect wifi and connect again it connects to the node upstairs. Tried to change some settings but no joy. What is...
  10. C

    Instant guard

    Has instant guard client 2 factor authentication?
  11. C

    Strange WAN connection issue

    Well mystery resolved. 😂 Factory reseat would have fixed :) but problem wasn't NVRAM... the IPTV page had a tagging for VLAN 10 with my previous provider but totally forgot :) Removed the tag and all good. Still hard to understand how was working fine with Wan aggregation with only main...
  12. C

    Strange WAN connection issue

    Sorry issue with images in previous post... All good with Wan aggregation on, error your ISP DHCP is not working properly is gone. If I change back, error comes back
  13. C

    Strange WAN connection issue

    Using Wan aggregation works (1GB ISP). Tried the suggestions of leaving it off for 30 minutes no joy. Also tried the settings in the screenshots. Sys log doesn't show any error or WAN down. Only way I get it to work is with the WAN aggregation enabled see attached . What is the difference...
  14. C

    Strange WAN connection issue

    Hi Using AX86u with latest merlin firmware. Was using fibre ISP directly connected to the ASUS all good. I switched to Virgin media and using their router in Bridge mode. They are a cable ISP. I used them before with asus and merlin and no issue. Now seems that unless I setup the internet wan...
  15. C

    VPN Policy rules director

    Did set up the openvpn client to express vpn and policy rule in director for client .223 to go through vpn but traffic is not redirected. Anything else I need to do? Never used dierctor before but when I used the old way of redirecting traffic never had a problem
See more
Back
Top