Recent content by Darkje

  • ATTENTION! As of November 1, 2020, you are not able to reply to threads 6 months after the thread is opened if there are more than 500 posts in the thread.
    Threads will not be locked, so posts may still be edited by their authors.
    Just start a new thread on the topic to post if you get an error message when trying to reply to a thread.
  1. D

    Beta ASUSWRT 386 RC2 public beta with full functions AiMesh 2.0

    @ASUSWRT_2020 so i checked with @RMerlin and i Wanted to know why in dual wan / balanced trendmicro wont work. Can IT be enabled?
  2. D

    [Thread-1] [ 386.1_Alpha Build(s) ] Testing available build(s)

    Can you enable IT on dualwan?
  3. D

    [Thread-1] [ 386.1_Alpha Build(s) ] Testing available build(s)

    Same router, no issues at all. @RMerlin any reason why i cannot use trendmicro when router uses loadbalancing.
  4. D

    [Thread-1] [ 386.1_Alpha Build(s) ] Testing available build(s)

    @RMerlin so if iam not mistaking the 86u and the gt-ac2900 are same products with different software right?
  5. D

    Beta ASUSWRT 386 RC2 public beta with full functions AiMesh 2.0

    So actually i found out (by accident) that above is not true. And i checked it 2 times. With you firmware it does combine the 2 lines in the speedtest. After i did a full reset (did that before offcourse).
  6. D

    Beta ASUSWRT 386 RC2 public beta with full functions AiMesh 2.0

    Sounds fair enough. Al tho then it would be nice to have a WAN selection so both connections can be tested. And or selected like system wide.
  7. D

    Beta ASUSWRT 386 RC2 public beta with full functions AiMesh 2.0

    @ASUSWRT_2020 So i just wanted to see what was up so i installed it on my 86u. And all seems ok (offcourse known issues aside). Only one remark. speedtest uses only one connection. And since i have 2. That dont seem to work. Tryed the alpha2 of @RMerlin and it gives me the same issue. I use...
  8. D

    386.1 Alpha?

    Yes that should be awesome. I have 2 cable modems active. And i do loadbalancing and IT works awesome. Just all trendmicro dont work. So yeah i agree
  9. D

    VPN Loadbalancing

    Yeah wel i can connect 5 VPN's simultainous. I just dont know how to loadbalance them to one ore multiple IP's @RMerlin perhaps you are able too help me out ?
  10. D

    VPN Loadbalancing

    So guys and galls, i was looking for a way to loadbalance on the VPN. So i could combine multiple VPN server to multiple connections. So when gets maxed out (set the speed yourself) it wil push to or add a other VPN server. Does this sound possible ?
  11. D

    Need solution 86u behind router

    So dmz wil be the way to go. I Just done like this verry much. Insure hope IPTV Will still work in this setup.
  12. D

    Need solution 86u behind router

    @Zonkd it Will be a Expedia box v10
  13. D

    Need solution 86u behind router

    Hey all, i have a issue. I have a 86u as router with VPN in and out. All works awesome. I have a bridged cable modem. Iam most likely getting a new isp. Based on bonded vvdsl The problem is they dont support bridge mode. So how can i keep using my 86u and all VPN options. Hope you all know.
  14. D

    [AC88U, 384.15] 2.4GHz WiFi channel setting is not respected

    i can confirm, the setting does not stick either way. (86u)
Top