Recent content by ds5686920

  • ATTENTION! As of November 1, 2020, you are not able to reply to threads 6 months after the thread is opened if there are more than 500 posts in the thread.
    Threads will not be locked, so posts may still be edited by their authors.
    Just start a new thread on the topic to post if you get an error message when trying to reply to a thread.
  1. D

    ActionTec 2.5 MoCA Adapter IP Address?

    Found answer here https://forums.verizon.com/t5/Fios-Internet/How-to-config-G1100-for-Actiontec-ECB6250/td-p/907112 The MoCA Adapter default Ip address is 192.168.1.1 so set your PC to 192.168.1.10 1 with 192.168.1.1 as Router Address and '255.255.255.0' for network mask. Direct connect from...
  2. D

    ActionTec 2.5 MoCA Adapter IP Address?

    I have two of the current model ActionTec 2.5 Gbps MoCA Adapters I use to extend my WiFi network (4 floors including garage). How do I find the IP Address assigned to an adapter's Ethernet port? It appears like a ghost where my software network tools don't see the adapter. The MAC Address...
  3. D

    Firmware Bug Between Access Points - Client List Categories?

    Here is part of the client list category on the AP in question. The MACs that begin with '8C' are OHLUX Smart Bulbs which connect on 2.4 Ghz band.
  4. D

    Firmware Bug Between Access Points - Client List Categories?

    I installed a switch and plugged both APs into it then plugged switch uplink port to Firewalla. Everything works but problem remains.
  5. D

    Firmware Bug Between Access Points - Client List Categories?

    Yes, not using a intermediary switch between the two APs. I have switch so will give it a go to see it makes a difference.
  6. D

    Time machine and AC86U

    I gave up on it when I found out had to use HFS+.
  7. D

    Firmware Bug Between Access Points - Client List Categories?

    I should add the MoCA connection is directly between the APs. I don't know why this would cause a problem though because a switch is a switch.
  8. D

    Firmware Bug Between Access Points - Client List Categories?

    I have a RT-ACRH13 AP in Loft (3rd floor connected to Firewalla Gold which is the DHCP server). To extend this AP I added a RT-AC1200 V2 AP via MoCA in Living Room on first floor. This network segment is for IoT like light bulbs. Both Access Points list 38 Clients which makes sense but 34...
  9. D

    RT-AC68U V3 Core #2 Pegged to 100%?

    Checked the log file and realized the router never executed the remote reboot! Unplugged power to reboot...problem fixed.
  10. D

    RT-AC68U V3 Core #2 Pegged to 100%?

    I can't ssh in. I have ssh server on (telnet off) and am refused connection. Using MacOS Terminal's 'ssh' command.
  11. D

    RT-AC68U V3 Core #2 Pegged to 100%?

    I found the UPnP Media Server setting,. It was ON and I turned it OFF however Core2 still at 100%.
  12. D

    RT-AC68U V3 Core #2 Pegged to 100%?

    It goes to 100% right after I log in after reboot. I am not using USB on router. I am using it in AP mode. Not sure what Media Server is.
  13. D

    RT-AC68U V3 Core #2 Pegged to 100%?

    It's running 3.0.0.4.386_43129. I rebooted it and Core2 goes back to 100%. Should I reload firmware?
  14. D

    OHLUX 900 Lumen Smart Bulb

    By slightly unscrewing each bulb I was able to achieve a good signal for all three bulbs by repositioning the RF board.
  15. D

    RT-AC1200 Head Scratch

    So is the 5Ghz in there just to get more channels so lessen neighbor interference?
Top