Recent content by dwadj

Did today the update to Alpha 2 and AiMesh is now working without any resets of nodes, so was it some glitch or just bad luck with Alpha 1.

Yes it is

Mmm did't do it because it was never an issue before. Also the wired devices were connected on the nodes, so nodes are recognized and should work. I'll try again when the beta phase starts.....

I also did the update from 102.6 to this alpha build, only on the main AX-11000 pro router. However with 102.6 the Mesh system behaves like expected, clients get roamed most of the time to the best available Node, with 102.7, only the wired clients are on the nodes, wireless clients seem to be...

I got a AiMesh setup with guest network pro setup for the IOT devices. Main router GT-AX11000 pro is running 3006.102.6_beta2 as well as the Aimesh node GT-AX11000 pro. The Reolink is connected on a AiMesh node (GT6) with the IOT network. However it is not shown as IOT device in guest network...

Hi Mutzli, Yes done this same behaviour, but at least with the main router running on stock i could add the nodes again, with the Merlin firmware not. So i did set it up with all routers (main+nodes) on stock, but also in this scenario node3 who connects through wifi will only connect on 5 ghz...

I all did that, but no luck. Ideally speaking that last node should connect to the 5ghz backhaul of the AX11000 pro node, because of the best signal, however it can only for some unknown reason connect on 2,4 ghz. It can however connect to the main router on the 5Ghz backhaul, with worse signal...

I have a Aimesh setup with main router GT-AX11000 PRO, nodes with wired backhaul are again one GT-AX11000 PRO and one GT6. Then there's a 3rd node with wireless backhaul also a GT6, all AX11000 running latest merlin 3006.102_5, where the GT6 are running latest asus stock 3.0.0.4.388_24675 Now...

Maybe stupid question but i have the ASUS GT-AX11000 PRO It's running latest alpha 3006.102.6, so according to Merlin's notes merged GPL 3006.102_37957. Now Asus has also released a new firmware version 3.0.0.6.102_34815 It's 37957 vs 34815 ! For the GT-BE98 they are on 3.0.0.6.102_39115. So...

Yes i can trail and error but this works on AsusWrt so same should also work on Merlin's

That should not be needed, since it's a fork of the official one. When time tomorrow i'll do it again with a full reset

Went again from Asus official GT-AX11000 Pro Firmware version 3.0.0.6.102_34750 to this latest Beta . For some reason clients like the Freezer, espresso maker, ... are not connecting to the router. Same settings no luck in Merlin firmware, other clients have no issue. If i revert back to the...

Yes of course, but it should not matter, because i was already on the 3006 from Asus.

I also update my GT-AX110000 pro (main + node in AIMesh wifi 5G2 as backbone) from official Asus 3.0.0.6.102_34750 to this beta.... At first it looked ok, however in AiMesh this beta is not working... Some clients would not connect and others are constantly connecting/disconnecting. Checked all...

mmm strange, running the Ax11000 pro on 3.0.0.4.388_24721 and the node Ax11000 (non-pro) with merlin 3004.388.7 but no issues, more or less same speeds as on 3.0.0.4.388_24199 or merlin 3004.388.7 on main AX11000 pro. Maybe an issue with gt6?