Menu
What's new
By:
Filters Better Search

Recent content by florid

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. F

    How to setup an isolated VLAN on Merlin?

    Thanks for the info. Actually I've already ordered a Mikrotik hex poe 960pgs to replace RT-AC68U. 960PGS is a little bit weaker than asus 68U on the routing and NAT but I need its POE to feed couple cameras. It is much easier to configure VLAN on RouterOS to work with Cisco Aironet AP.
  2. F

    How to setup an isolated VLAN on Merlin?

    So a under $80 MikroTik ROS router can replace both main router and 4 ports manageable switch with granular VLAN function plus POE.
  3. F

    How to setup an isolated VLAN on Merlin?

    @ccl13 not sure whether you have found a good solution for this? I have exactly the same requirement at home. I want to use RT-AC68U as main internet router with Guest wifi limit intranet access. I have a Cisco AP attached to AC68U lan port. I want to broadcast the segregated Guest wifi on Cisco...
  4. F

    [Release 384/NG] Asuswrt-Merlin 384.4 is now available

    same dual wan load balance issue since 384.3 on RT-68U. Not able to load SSL pages in load balance mode. Works fine with failover mode.
  5. F

    [Release 384/NG] Asuswrt-Merlin 384.3 is now available

    This version’s dualwan definitely not work in load balance mode. Tried to enable/disable route rules, no help to fix Internet access issue. I can see the connection out but in time waiting status. Seems like the TCP handshake cannot properly established or the return packs are not properly...
  6. F

    [Release 384/NG] Asuswrt-Merlin 384.3 is now available

    I know dualwan code is closed. But this version dualwan seems not quite function. Disabled aiprotection dns filter which conflicts with dualwan lb mode not solved everything. LB mode has some kind of slowness and timeout issue that hard to troubleshoot. I have to put dualwan into failover cold...
  7. F

    [Release 384/NG] Asuswrt-Merlin 384.3 is now available

    Upgraded my 68U to this version. Did a factory initiate and manually change the configuration. Just notice some issue with dualwan. Syslog prompts trendmicro not works in dualwan load balance mode. For the Internet access, seems some issue to access google.com. Timeout at tls handshaking. But...
  8. F

    Raspberry pi 5 GHz adapter No internet when connected directly to RT-AC5300

    The picture shows no default gateway.
  9. F

    use case in upgrading from rt-ac68u with 800 MHz to 1GHz

    It’s just a wireless router. Even you get CPU to 1.6Ghz it is still a router. If you want to play with a server, buy a NAS (recommend)or Pi (budget choice).
  10. F

    Is it possible to temporarily change port forward rule from command line on asus rt68ac?

    Use acme.sh. see this guide. https://github.com/Neilpang/acme.sh/wiki/Synology-NAS-Guide
  11. F

    User-provided SSL certificate for webui

    you can create a dnsmasq server entry to resolve YOURDOMAIN.com to 192.168.100.1 internally.
  12. F

    RT-AC68U randomly losing connection with Onkyo receiver

    Perhaps I have a similar issue with Marantz. The receiver NIC is 100M. And I can tell the network chip is very weak. What I did, 1. check the cable 2. force to set the interface speed to 100M on switch if possible 3. use fixed static IP address instead of DHCP 4. check the network setting on...
  13. F

    USB GPS instead of NTP

    the router has to been placed under the sky?
  14. F

    Please Help! RT-AC68U wifi can't connect

    I had similar wireless connection issue after applied some change to malicious blocking scripts. Cannot connect wireless. But the connected clients can still access network. I did a factory reset and a power cycle to back it normal. I have no idea but only observed some weird syslog. Seems like...
  15. F

    Password auth succeeded for 'admin'

    How they did that? Have you ever allowed management access from WAN?
See more
Top