What's new
By:

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by inquam

  1. I

    Upload speed capped after installing Merlin

    Strange, after sitting on swedish bredbandskollen, speedtest, dslreports and just running speedtests over and over it now gives me 243Mbit/sec upload and 247Mbit/sec download. Does the router have to "learn" what speeds are available?
  2. I

    Upload speed capped after installing Merlin

    I'll give it a shot. I did a factory reset and left it unplugged for about a minute but still maxed upload at ~180MBit/sec. Will try to leave it off for a bit longer. p.s. See this in the log if that means anything Aug 1 00:00:14 kernel: * Invalid signature of oopsbuf: D7-FD-F3-5E-EA-FE-37-D7...
  3. I

    Upload speed capped after installing Merlin

    Yea I'm using a wired cat5e network at home I think I initially did. And I got 150MBit/sec when I first started using Merlin. But then over time, some updates and settings later I arrived at this. I'll try this again later tonight... Will suck though since I had a lot of OpenVPN and wifi...
  4. I

    Upload speed capped after installing Merlin

    Tried roling back but still the same. I noticed that if I kept running the test over and over it would slowly climb a bit. So even in .59 it's now giving me around 170MBit/sec and the same in .58. But if I connect directly to the fiber box I get 248MBit/sec
  5. I

    Upload speed capped after installing Merlin

    Nope, no QoS, Apps analysis, Web history. Traffic Analyzer - Statistic is not enabled either. I have tried disabling the firewall on both ipv4 and ipv6 but no change. Just scratching my head here :P
  6. I

    Upload speed capped after installing Merlin

    Strange thing now is that if I set it on auto it will not say FA, only CTF. edit: Once I tried turning "Malicious Sites Blocking" off again FA was once again printed as active. But a test still only got 158Mbit upload speed
  7. I

    Upload speed capped after installing Merlin

    Tried turning it off, rebooting, back on, rebooting but still the same. One thing changed though. Now it doesn't say "CTF (Cut Through Forwarding) and FA (Flow Acceleration) accelerator are enabled." anymore but instead only "CTF (Cut Through Forwarding) is enabled."
  8. I

    Upload speed capped after installing Merlin

    Where can I fint that setting? edit: Not sure if this is correct but under "LAN/Switch Control" NAT Acceleration is set to Auto and "CTF (Cut Through Forwarding) and FA (Flow Acceleration) accelerator are enabled." printed besides it
  9. I

    Upload speed capped after installing Merlin

    I tried it again and forced a reboot to make sure. Exact same result. Upload maxes out at 145Mbit/sec. During the speed test the cpu usage on the router hovers in single digits for both cores.
  10. I

    Upload speed capped after installing Merlin

    I have a single port forward, wifi 2.4 and 5ghz setup, AiCloud 2.0 "Cloud Disk" and "Smart Access" enabled (but no disks plugged in) and one Open VPN server. I tried turning the VPN off but that made no difference. This was about to be my response. But I remembered that I actually activated...
  11. I

    Upload speed capped after installing Merlin

    I have Fiber in my house and had my Asus ac68u connected to the fiber box. With the stock firmware I got about 245MBit/sec down and 247MBit/sec up. Since my subscription is for 250/250 it's quite close. I then installed Merlin 380.59 and after that I still get around 240MBit/sec down, but my up...
See more
Back
Top
✖