Recent content by joebloogs

  1. joebloogs

    Wireless > Site Survey not detecting any 5Ghz signal after upgrading to 386.5_2 version

    I never use wireless MAC filter...it's disabled, so that is not the issue in my case.
  2. joebloogs

    Wireless > Site Survey not detecting any 5Ghz signal after upgrading to 386.5_2 version

    After upgrading to latest 386.5_2 version, my RT-AC68U does not detect any 5Ghz signal on Wireless > Site Survey....only 2.4Ghz When i go back to previous version i get both 5Gz as well as 2.4Ghz.....is there a fix for this?
  3. joebloogs

    RT-AC68U poor 5Ghz performance

    yes M8...same router...now that you mention it, i went & had a look at my previous posts and found out i had 5Ghz speed issues back in 2017... also had a look at the date i made those posts and i think i know the problem now... When i first noticed this problem back in 2017 was when i had just...
  4. joebloogs

    RT-AC68U poor 5Ghz performance

    I have factory reset my router with latest Merlin to factory defaults, Initializing all the settings, and clearing all the data log for AiProtection, Traffic Analyzer, and Web History. I must note I am using wifi Sweetspots app on my devices to measure wifi signal quality.. tested each non DFS...
  5. joebloogs

    RT-AC68U poor 5Ghz performance

    my devices are all ipads & iphones with latest iOS versions installed, so that should rule out device driver issue... I am aware of distance limitations of 5Ghz range, but i cannot get any signal improvement over 2.4Ghz even in the same room as my router!!
  6. joebloogs

    RT-AC68U poor 5Ghz performance

    as already stated nearby 5Ghz signals are very weak so not sure if i can blame them...as for my clients...i tried with 3-4 different devices with no luck.. is there a way to check the hardware?
  7. joebloogs

    RT-AC68U poor 5Ghz performance

    5Ghz on my Rt-AC68U is worse than 2.4Ghz and what ever i done has not improved it...(no complaints with 2.4Ghz) Was running latest stock firmware up to now with no luck, so i switched over to Merlin 386.3.2 but still no joy! Is there some secret setting i need to change to get the 5Ghz working...
  8. joebloogs

    Configuring Dual WAN

    pleased to say i have now managed to configure my RT-AC68U as it should & fixed my Dual Wan connectivity issues...it is now working perfectly.. I just followed the instruction on the page below https://www.asus.com/support/FAQ/1037368/
  9. joebloogs

    Configuring Dual WAN

    Same problem here...i cant get dual wan to kick in on my RT-AC68U either...this feature used to work many firmware updates ago but since it was so long ago i cant remember which firmware it worked last time..
  10. joebloogs

    RT-AC68U Dual WAN question

    Is there a way, (using the PC interface) to switch between two internet connections when using Dual WAN? Like, if i want to switch over to secondary connection from primary connection..
  11. joebloogs

    RT-AC68U 5Ghz transfer speed lower than 2.4Ghz..

    Just realized 5Ghz transfer speed is lower than 2.4Ghz on my RT-AC68U.. Tried playing around with the antenna positions to see if it changes but it doesn't. Previously 5Ghz used to be about 3 times faster than 2.4Ghz...any ideas why this might be? Router running latest stock firmware...
  12. joebloogs

    RT-AC68U firmware 3.0.0.4.382.18547 slows down 5Ghz Wireless.

    i decided to try out the latest merlin version...so far I cant fault it..
  13. joebloogs

    RT-AC68U firmware 3.0.0.4.382.18547 slows down 5Ghz Wireless.

    any idea how to boot into recovery mode?
  14. joebloogs

    RT-AC68U firmware 3.0.0.4.382.18547 slows down 5Ghz Wireless.

    I rolled back to 380.7743 and this has doubled up my 5Ghz WI-FI transfer speed but still it is around 170Mbps average.. When I purchased the router about 1.5 years ago I used to get speeds over 400Mbps!! I use an app called Sweet Spots on my iphone & ipad to measure speed.. I wonder if it will...
  15. joebloogs

    RT-AC68U firmware 3.0.0.4.382.18547 slows down 5Ghz Wireless.

    I have the same issue on 5Ghz wireless. running Version:3.0.0.4.382_18881 will it fix the problem if I roll back to 380.7743?
Top