Recent content by lodester

Turns out I have a USG20 still sitting around as I was going to return because it's a bit on the small side, but it works great. Got it configured and I can access my services now after the first attempt at setting up the forwarding rules. I'm just going to throw the AC66U in to AP mode and be...

As I said, perhaps poorly, the packet count does not increase. Also yes, I did use the correct syntax for the FTP server. These services were working, this has all happened before. These ports are not being blocked, I promise you the moment I hardware-reset the router and put the exact same...

@john9527 , this is for a very flat SOHO environment, few active clients, about a dozen or so servers that don't typically move a lot of data @RMerlin , Thanks for that, I didn't do any testing this go-around because I've seen this twice before and just sort of wrote it off, but I believe...

Ah, i probably could have figured that out for myself, anyway, doesn't look like nvram is exhausted: size: 43242 bytes (22294 left) :(

@RMerlin , thanks for your reply. CTF was disabled, so that's no help but a good thought. I did apply the 4850 update and cold restarted the router afterwards - no help there either, unfortunately. @john9527 , thank you as well. I think you may be referring to a UI element in a custom ROM for...

First of all, that's not how Port Forwarding works. You're allowed to say WAN port 3333 go to IP address xxxxx , port 21. What you're configuring is implicit 1:1 port mapping, which is valid, but it's not "how to forward ports" it's one way to forward ports on a 1:1 basis. Second, what you...

You haven't been working with retail electronics very long. It's entirely possible your router doesn't have this flaw but you are absolutely wrong. I know you think you know how every RT-AC66U works down to the wire, but your statement is plain wrong. I've got one right here that routinely quits...

@teapa , if you factory reset your device you'll be able to port forward.... for a while. This has been a problem with this router since the first day it shipped. There is no setting or combination of settings that fixes it once your RT-AC66U decides to no longer forward traffic, period. ASUS...

Thanks for the reply. I understand that there are multiple factors that determine throughput capacity for any given transfer - my point was it is clearly not the hardware holding things back. a 75% reduction in capacity though is a pretty unacceptable software implementation. How can anyone...

Hi everyone, I am trying to figure out why my new 559 P2 rsync jobs are stuck at around 10MB/sec. Some facts: 1) The two NAS's are on the same switch and negotiate to gigabit speeds. 2) There is no other activity on either NAS 3) The target (ix4-200d) is capable of far greater write throughput...

Thanks - sorry i didn't notice that, i don't frequent these boards but i did just reply. I wish I had seen that sooner, oh well...thanks a ton, though. Let's bring the story up to date... After I got my disks and data back from data recovery, on the 13th of June I contacted Iomega to take the...

So the drives came back, I'm doing the data copy now. Next step is letting iomega know I have the original array disks back and how they want to handle this. Not surprisingly nobody from iomega ever followed up with me on what options I have at this point and to date for this one issue three...

Thanks for replying but disabling write cache and living with intermittent lockups and the general crap that is IOMEGA is absolutely unacceptable. It's like buying a car then finding out the fine print says "Car max speed is 40 mph and if driven on odd numbered days there is a chance of...

Iomega ix4-200d software lost stripe; stay away So i have to tell this place about this horrible experience with Iomega. I feel I should give at least a little back here as I've been lurking around SNB for a few years now looking and reading up for my SOHO NAS purchases. Excellent...