What's new
By:

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by ludespeedny

  1. L

    Speed issue, where to start

    Thanks, but I actually tried their version 3.0.0.4.388_24323 as well as Merlin's 388.8_4 and 388.2_2
  2. L

    Speed issue, where to start

    I have a few more ideas to try, but have to wait till next week. One is to get a small gigabit switch and put between ONT and router and see if it fixes.
  3. L

    Speed issue, where to start

    Just checked and warranty expired last month. Guess time to look for another one.
  4. L

    Speed issue, where to start

    Yeah, link is only 100/100 from other pc's to the WAN and 2.5gb port. Everything was run new. and tested. ONT is inside in the basement and I tested with router right next to it with 4 different cables. So right now, I'm not even on the long cable run yet. Connecting pc's to the ONT via the...
  5. L

    Speed issue, where to start

    Yup, that's the method I did.
  6. L

    Speed issue, where to start

    Did a factory restore via settings as well as the wps method. Issue persists. @oldgringo I'll try a self test on the ports if I can figure out the log.
  7. L

    Speed issue, where to start

    I assume I do it via admin page and "initialize all settings" correct?
  8. L

    Speed issue, where to start

    I tested directly at the ONT with 3x different good cables all Cat 5e or better. Same results. Plugging into lan ports 1-4 show 1g connection and wan or 2.5gbe ports only 100mb connection. I also plugged into my old isp router/modem with the same results so I am thinking maybe my router wan and...
  9. L

    Speed issue, where to start

    Plugging into one of the lan ports shows green and full connection. No dust etc in the port. I'll try to go directly into the ONT later with a short patch cable. But all the cabling in house was run fresh this am. I can get a cable tester from work on Mon, but suspect the router port. Is there...
  10. L

    Speed issue, where to start

    brand new run. but am getting this: link speed directly to my laptop negotiates to 1000/1000 but router is 100/100
  11. L

    Speed issue, where to start

    Today I switched ISP's and should have 200/200. When I am plugged in to my router I only get half that. If plugged directly into the line, I get full speeds. I have an Asus RT-AX86U on merlin's 3004.388.8_4 build. I am running diversion, but turning that off seems to make no difference. Can...
  12. L

    Wifi issues, where to start diagnosing

    *update All seems to be good. No issues with disconnects. I'll assume it was due to DFS channels. Thanks for the help!
  13. L

    Wifi issues, where to start diagnosing

    I have it disabled, but will stick to manual channel for now. What channels specifically are DFS?
  14. L

    Wifi issues, where to start diagnosing

    Got the wifi disconnected message only once last night on the TV and that was after powering on, so I assume it was from it coming out of standby (which I am ok with), at least it didn't keep popping. PI is still up this AM. I'll try re-enabling diversion today and see if anything changes (I...
  15. L

    Wifi issues, where to start diagnosing

    *Update I was making the changes and rebooted the router. Then rebooted the devices with issues. I was unable to get the Pi to connect. I noticed the channel on wifi changed to 136. I changed it to 36 and it was able to connect. I wonder if the auto channel change was preventing it from...
See more
Back
Top
✖