Recent content by mvadu

  • ATTENTION! As of November 1, 2020, you are not able to reply to threads 6 months after the thread is opened if there are more than 500 posts in the thread.
    Threads will not be locked, so posts may still be edited by their authors.
    Just start a new thread on the topic to post if you get an error message when trying to reply to a thread.
  1. M

    Solved Enable/Disable guest network on schedule (crontab)

    #!/bin/bash ## /jffs/scripts/reset_guest_wifi.sh # echo cru a vpnon "0 7 * * * /jffs/scripts/reset_guest_wifi.sh" >> services-start ## Script to restart guest networks guest1=$(nvram get wl0.1_bss_enabled) guest2=$(nvram get wl0.2_bss_enabled) guest3=$(nvram get wl0.3_bss_enabled)...
  2. M

    Solved Enable/Disable guest network on schedule (crontab)

    ah.. I should have just kept keep scrolling. I went into the links and got lost.. Thank you that pointer @ColinTaylor
  3. M

    Solved Enable/Disable guest network on schedule (crontab)

    also tagging @L&LD as well
  4. M

    Solved Enable/Disable guest network on schedule (crontab)

    @RMerlin sir, any luck you can provide the command we can run on the shell which will enable/disable given guest SSID?
  5. M

    Beta Asuswrt-Merlin 386.3 beta is now available

    with DNS set to "Exclusive" does the router still resolve the local peers? With the older firmware clients using the tunnel with DNS set to "Exclusive" would not resolve the local peers even though they are using router as DNS server. Is it something that can be done (i.e. to allow for local...
  6. M

    Solved Enable/Disable guest network on schedule (crontab)

    The actual command linked there is no longer available
  7. M

    Solved Enable/Disable guest network on schedule (crontab)

    I have few Tasmota IOT devices running on ESP8266 chips. They have some compatibility problem with Asus AiMesh they keep going in loop trying to connect and failing to connect (no error in Asus side, but device thinks it couldn't find the access point. What I have noticed is if I stop and...
  8. M

    RT-AC86U WiFi issues with 386.2_4

    I have been facing this same issue for quite some time with one of my Tasmota (esp3288 from Espressif board) devices. I have a mesh with ac-86u primary, and ac-3100 node. 2 other Tasmota near 3100 work just fine, one sitting 10 inches from main router acts up. All of them connect to guest...
  9. M

    Solved upnp throwing ConflictInMappingEntry even though port is free, target is local host

    quick update, Mr. Thomas Bernard did consider this bug and has fixed it. The fix is scheduled for miniupnpd_2.3 milestone.
  10. M

    Solved upnp throwing ConflictInMappingEntry even though port is free, target is local host

    I am not disabling secure mode, but restricting allowed client to only one. I have two corporate issued laptops in household which have few software which tends to open way too many ports if allowed is list is default all local lan ( 192.168.23.1/255.255.255.0 in my case), my post conf updates...
  11. M

    Solved upnp throwing ConflictInMappingEntry even though port is free, target is local host

    well, the error didn't say anything about wrong IP segment, it did not complain about incomplete config. Look at samba or nginx, which expects a solid config before starting, and it makes troubleshooting much easier. I did open the issue not sure if maintainer will accept it or not.
  12. M

    Solved upnp throwing ConflictInMappingEntry even though port is free, target is local host

    @sfx2000 I am running the miniupnpc on raspberrypi itself.. but as you can see in above comments, I had a post conf script in router (Which runs on router startup) which was screwing up the config, causing it to miss the allowed subnet. Probably I should open an issue in github for miniupnpd. If...
  13. M

    Solved upnp throwing ConflictInMappingEntry even though port is free, target is local host

    I did add that check when I found out the upnp.postconf was the creator of this problem. but without local dnsmasq it was always skipping.
  14. M

    Solved upnp throwing ConflictInMappingEntry even though port is free, target is local host

    Thank you.. that seems to be working. Let me add it to the script, and "pretend it never even happened"
  15. M

    Solved upnp throwing ConflictInMappingEntry even though port is free, target is local host

    @dave14305 you brought up a good point. I totally forgot that I have a upnp.postcof script which was suppose to block all hosts except this one raspberrypi. For some reason on the router its not finding the local clients and my script basically screwed up the config. cat...
Top