Menu
What's new
By:
Filters Better Search

Recent content by Nubble

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. N

    dhcp lease store on jffs

    John, thank you! I know this is an old post but the information posted here showing and explaining what's needed to allow the firmware to access DHCP information from the lease file has allowed me to view both DHCP lease and wireless client details through the GUI interface. I do a lot of my...
  2. N

    QOS bandwidth limitation per device below 1Mb/s

    When I use a decimal (like .5 or .7) to indicate a portion of a Mb/s bw it seems to work fine for me when I test. I've bee using it for a while now. .1 Mb is as granular as you can specify which seems quite reasonable.
  3. N

    Traffic Monitoring Log

    Check the file size. If not empty make a copy of it and then delete it. If this doesn't resolve the issue then request that it be recreated through the GUI. It's also possible a reboot will resolve your issue.
  4. N

    Traffic Monitoring Log

    Not sure this will help but I had the same issue - it had been working but this error occurred after a reboot. I ended up overwriting the file from a prior backup (I've learned to backup these files through cron and on a reboot) and it immediately began working again. Problem has not reoccurred.
  5. N

    Identify guest network clients

    Nice. Wasn't aware dnsmasq could be event driven. Will attempt a variation of this myself.
  6. N

    Identify guest network clients

    In terms of other functionality, if the function(s) you're referencing are granular at the client level then if shouldn't matter their origin (from the LAN perspective) whether Wired or Wireless, or which SSID. Be aware when setting up a Guest network that restricts local intranet access there...
  7. N

    Identify guest network clients

    System-Log-->Wireless-Log. "G" in Flag column indicates Guest. As far as I am aware you cannot tell which Guest network other than the 2.4 -5 GHz designation.
  8. N

    System Log - Deleted

    This is certainly possible however as a test, I clicked "Clear" in the UI and indeed syslog.log (and apparently syslog.log-1) was deleted from the /tmp directory. If I issue a process (PS) command for syslogd I don't see anything that implies a reset, but output from this command is limited. Any...
  9. N

    System Log - Deleted

    I must have inadvertently clicked "Clear" on the system log GUI page at some earlier point as when I went to view it much of it had disappeared. I lost valuable troubleshooting information as a result of that mistake. (I honestly don't recall doing this.) I was able to recover the syslog.log-1...
  10. N

    Bandwidth limiting?

    If you were to extend this logic then it would not include 192.168.x.16 or 192.168.x.47 either. In this case the presumption is this is not defining a subnet (with associated subnet and broadcast addresses) but merely a range. This type of summarization is used in routing tables. Whether is...
  11. N

    Bandwidth limiting?

    I'm sure many others here could explain this easier and better than I but I'll give it a try. I'm presuming the IP addressing is being expressed in CIDR notation. As we know an IP4 address is 32bit binary expressed as 4 octets separated by periods. Additionally that address is associated to a...
  12. N

    Bandwidth limiting?

    192.168.x.16/28 192.168.x.32/28 The above two entries would cover IP range 192.168.x.16-192.168.x.47 inclusive.
  13. N

    Bandwidth limiting?

    Assume 192.168.x.130/25 should actually be 192.168.x.128/25.
  14. N

    [Release] Asuswrt-Merlin 380.63_2 is now available

    Email sent. Sorry for the delay, traveling for US holiday. Your assistance is greatly appreciated!
  15. N

    [Release] Asuswrt-Merlin 380.63_2 is now available

    Hi, thanks for your quick reply. As this is not the same issue that was in the beta build, has not been reported by anyone else, and it may not be related to any of your code, I did some more investigation. The .ovpn file was generated from a RT-AC66R router (openvpn server) that I recently...
See more
Top