Recent content by pendetim

Scripting was enabled. And I reformated the JFFS and rebooted. Still no services-start, just emptyness. If I use WinSCP to create this services-start file and edit the contents to add the string above, is there any permissions stuff that needs to be done? Another question, please. How often...

Great directions. Giving me confidence to try this!!!! But still a little nervous. I do have a grandfathered account with 3 a few clarifications, please. Will PuTTY give me the terminal window? Can those commands to test be run from the root directory level in the PuTTY window? There is no...

Thanks for the idea. However I have absolutely no idea how the add a cron job. I am a real NOOB at this stuff. Sorry. My configuration is as follows: 3 Asus Routers at different locations, call them Cable, Creek and Green 3 Networks on OpenDNS with Names Cable, Creek and Green 3 Networks...

Thanks, Again. I am trying to use OpenDNS service with some custom filtering at several sites as well as keep the dynamic address updated so I can access a P2P VPN and do some remote management. Would you ( or anyone else reading this ) know if there are any other DDNS services that can feed...

Thanks for the reply. If I use "all.dnsomatic.com" it updates all 3 networks. I only want to update "cable.dnsomatic.com"

On a Asus RT-68 I am trying to use the built in DDNS updater for one of 3 networks I have on DNSOMATIC and don't think it is working. On DNSOMATIC I have 3 routers that I am tracking with network names of "Cable", "Creek" and "Green". They are linked to 3 networks on OpenDNS. My...

I went ahead about a week ago and setup the Asus Rt-AC68 as a dual wan with failover/failback. I had nothing to loose if it did not work as reverting to single WAN would be easy. After a week of using it and testing simulated and real failures from the cable WAN, I can report that it seems to...

I am considering using the Dual WAN in Failover mode on a RT-AC68 with 3.0.0.4.384.32799. The WAN connection is a cable modem, 30x3mbps speed and the LAN1 will be a DSL modem ,3.0 x0.78 speed. All values in the ASUS will be left at factory defaults for failover and fail back with a ping to...

Thanks. I am getting my confidence up! Can I name the new script anything that makes sense to me or are only certain file names permitted?

Thanks for the heads up. I have 2 other "true" Asus RT68 routers that I can use for establishing a VLAN. Still looking for guidance.

Hi, I am going to be trying to add a VLAN to port 4 on my RT-AC68 with Merlin firmware and am a COMPLETE noob. I think I understand how to putty into router ( converted it from a T-Moble version ) but a few questions about the instructions in this thread. 1. Is there any specific naming...

I have the 4 devices on separate "sub-accounts" with VOIP.MS. so concurrent registrations are achieved through these independent sub-accounts. Each sub-account has it's own login username/password. Once the devices register, they are very stable, until that is the WAN they are using drops. I...

I have a Asus Rt-AC66W configured as a dual wan in load balance mode; Primary is Cable and Secondary is Verizon DSl PPPoE. The configuration is both WAN connections are active all the time and there is a 9:1 ratio set in the speeds for the load balance. If I fail either the cable WAN or the...

A basic (dumb?) question about pasting keys into TLS. I am not sure how the software parses the data but the instructions say to paste only ---- Begin XXXXX ---- and ---- END xxxx --- into the fields. Is it possible to slightly modify the field for example to read -----BEGIN CLIENT CERT-----...

Thank you Merlin for all the hard work and dedication over the years on this project! It makes the "iron" more than a doorstop.