What's new
By:

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by Poul Bak

  1. P

    Release Asuswrt-Merlin 3006.102.6 is now available

    Really bad idea, I only drink tea :D Seriously, this is definitely an Asus bug, not related to Merlin.
  2. P

    Release Asuswrt-Merlin 3006.102.6 is now available

    I have seen the same on BT10 (stock!!). My investigations: You have a multi-band network (5 and 6GHz) You have disabled MLO completely (on 'Wireless', 'MLO'). If I enable MLO globally (on 'Wireless', 'MLO'). then they are shown correctly. Note: You don't need to enable MLO backhaul on ANY...
  3. P

    IPV6 while in Access point mode ac68u

    Well, that's how I have done it and it works fine. How does your devices get an ip address when connected to the access point? Also what router do you actually have (one from last century)?
  4. P

    IPV6 while in Access point mode ac68u

    With an access point you simply setup everything regarding ip addresses (both ipv4 and ipv6) on the main router. Devices attached to the access point WILL get ipv4 and ipv6 addresses.
  5. P

    IPv6 and media bridge/repeater mode

    Come on, this post is more than 10 years old
  6. P

    My two router nurseries (November 2025)

    Off topic, but do you use double nat when testing routers?
  7. P

    My two router nurseries (November 2025)

    I have always wondered what that room looked like. I expected a crazy mess of wires all over the room. But this looks like a 'controlled environment' :)
  8. P

    DHCPDISCOVER & DHCPOFFER : every 5 min for a device thats offline?

    Try to physically remove power cable and see if that helps (just to know the reason).
  9. P

    Release Asuswrt-Merlin 3006.102.6 is now available

    Dirty flashed from beta2 (I factory reset, when installing beta1) Nothing to report.
  10. P

    Beta Asuswrt-Merlin 3006.102.6 Beta is now available

    I had this bug on my BT10 (stock - as access point), which takes care of my wifi. I found that enabling MLO on the 'Wireless' tab, 'MLO' made them show correct. Don't know if it's related at all, but you could try that.
  11. P

    What to replace a flaky RT-AX68U with (EU)?

    What ever you decide, definitely go for a wifi 7 router. And do it correctly, first minimal setup, upgrade to latest stock from GUI, then do a factory reset, again minimal setup. Let it run for at least 1/2 hour. Now flash Merlin, followed by factory reset. This time you can setup everything and...
  12. P

    Beta Asuswrt-Merlin 3006.102.6 Beta is now available

    Niche concept???????? Have you been in coma the last 10 years? :) At least Google thinks it important enough to make statistics: Ipv6 statistics. Half the world have ipv6 now! ...and I'm not blaming Merlin at all, this is on Asus.
  13. P

    Beta Asuswrt-Merlin 3006.102.6 Beta is now available

    ''BUMMER'' - but I kind of expected that. Thanks for investigating. Still embarrassing for Asus IMHO, ipv6 is almost 30 years old and still "Oops, we didn't expect ipv6".
  14. P

    Beta Asuswrt-Merlin 3006.102.6 Beta is now available

    If you're using 'www.asusrouter.com' or ipv4 address in browser, you won't see this - it's an ipv6 thing. Or do you actually see ipv6 addresses in log?
  15. P

    Beta Asuswrt-Merlin 3006.102.6 Beta is now available

    You're right, 'www.asusrouter.com' resolves to an ipv4 address only. People using that won't see this bug. The reason I use custom urls like 'https://myrouter.home' is that I can now connect to both routers' GUI (I have always hated ip addresses in browser). The only problem is that you need...
See more
Back
Top
✖