Recent content by Power2All

  1. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    Hi, Thanks for the link. I'm in the Netherlands, and I've checked which channels to avoid. So I set it to channels that do not affect these scanners, good point btw.
  2. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    I think the issue is solved. So far no crashes anymore, thanks for the help everybody !
  3. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    I had to search what you meant, but yeah, I put it to Wifi 5 instead of Wifi 6 to see if it would make the chipset stabler ? I enabled that again, let's see if it still stays stable.
  4. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    Let me know if this should be sufficient. If it still keeps crashing, I'll enable the automated restart of the modem again:
  5. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    Thanks. It crashed again after a week (without your settings). I'll apply your changes, but it's quiet annoying. I'm tempted to put a nightly "restart" of the router, cause it's quiet frustrating, when my remote connection stops working when it was running fine :/
  6. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    WPA3 was already disabled, it's set on WPA/WPA2-Personal for all the WiFi frequencies. Also turned some stuff off like WiFi6 and such, and beaming, which is what I read is only for old devices. See if these settings does anything.
  7. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    Ah I understood it wrong then, thanks for clarifying it. I'll try upgrading again later and disable WPA3. As for WiFi devices, I basically have 2 heating devices connected to 2.4ghz, my phone and my PS4 (who is turned of for a long while now).
  8. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    I'm not from the US, and this device was very expensive. Otherwise I'll keep it at a lower firmware, since the one I use now, was up for a week without a hitch. So something is still up with the firmware, but I do have a lot of traffic coming over it, so perhaps most users don't have it in use...
  9. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    Sadly, the latest BETA (3004.388.11_beta1_rog) is also a dud. It crashed now twice in the span when I notified about the installation (21 december 2025). I'm downgrading again to GT-AX11000_3.0.0.4_388_24403-gd4e3d0c_ubi.w as that one was not crashing last time. I've attached the log of the...
  10. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    Yah but I rather have a permanent solution, then a temporary fix. Yours I have been thinking about, until it crashed within 1 or 2 days...
  11. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    Done, I did also a factory reset as said by you. Let's see if it stays up for this week, I'll update here if I either got another crash, or if it works stable for a week.
  12. Power2All

    GT-AX11000 keeps crashing after every few days (WiFi so it seems), and need to hard-reboot to get it working again

    Good news, so far I haven't seen it crashing yet. Last time it even crashed within a day. Perhaps this is something for the developers to look into, where this instability comes from in the release after the one I use now ? See what has changed, and/or what could be causing it.
Back
Top