Menu
What's new
By:
Filters Better Search

Recent content by revengineer

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. R

    Voxel Custom firmware build for R7800 v. 1.0.2.105SF

    Thank you Voxel!
  2. R

    Log into R7800 web gui from different local subnet

    @Sizzlechest THANK YOU, THANK YOU, THANK YOU!!! This works indeed.
  3. R

    Log into R7800 web gui from different local subnet

    Understood! I have now tried this route on my pfsense firewall, which is my DHCP server and is the link between the two subnets. Unfortunately, without success. I think it's because the route into the subnet, where the access point resides, is generally working.
  4. R

    Log into R7800 web gui from different local subnet

    Thank you for the pointer to static routes. My understanding is that static routes are for traffic originating from the access point, and not for incoming packets from other subnets. I am happy to be corrected if I misunderstood. I reiterate that the routing generally seems to work because I...
  5. R

    Voxel Custom firmware build for R7800 v. 1.0.2.97SF

    Most of the details and my attempts to solve the issue are described in the post I linked with my inquiry. Beyond that I tried getting uhttpd to run on the telnet port to see whether the issue was linked to port 80 being blocked from other subnets. For this I tried modifying /etc/config/uhttpd...
  6. R

    Voxel Custom firmware build for R7800 v. 1.0.2.97SF

    @Voxel Can I please beg you to log at this post and tell me why I cannot access the Admin GUI in Voxel firmware 1.0.2.97SF in Access Point mode from a different subnet? Access point is on 192.168.3.2, I am trying to access from 192.168.1.10. I can log into SSH (so routing generally ok) but not...
  7. R

    Log into R7800 web gui from different local subnet

    I tried a lot of things but do not seem to get it right. I see others complaining about this issue across the internet without a solution. I think I may just have to accept that this router is flawed and move on.
  8. R

    Log into R7800 web gui from different local subnet

    I checked the ebtables yesterday and just again, they are empty too. So I am not sure what blocking the http access but letting through ssh and telnet. Perhaps it's in the configuration of uhttpd daemon; I looked at the config in /etc/config/uhttpd but there is nothing obvious.
  9. R

    Log into R7800 web gui from different local subnet

    The chain loc2net does not seem to exist on my R7800 running Voxel firmware v1.0.2.97SF. When listing the rules, my system shows as seen below. Essentially there seems to be no rules defined. I tried adding suggested rule to chains INPUT, OUTPUT, and FORWARD but gui access still gives "404 not...
  10. R

    Log into R7800 web gui from different local subnet

    I moved my R7800 with Voxel firmware and configured as an Access Point to a different subnet (address now 192.168.3.2). The access point is configured with a static IP. Now I cannot connect to the admin web gui from another local subnet (192.168.1.x). I can ping the R7800 from the .1.x subnet...
  11. R

    Kamoj Kamoj Add-on 5.1 Beta testing poll

    Could I get a beta invite please?
  12. R

    Custom firmware build for R7800 v. 1.0.2.75.1SF & v. 1.0.2.75.2SF

    To clarify, it's a softbrick since tftp can recover the device. The problem goes beyond unavailability of the web GUI. After transfer of the firmware, the power LED starts blinking white with a regular on/off cadence and this goes on endlessly. The hardwired network connections and radios never...
  13. R

    Custom firmware build for R7800 v. 1.0.2.75.1SF & v. 1.0.2.75.2SF

    E.g., https://kb.netgear.com/000059633/How-to-upload-firmware-to-a-NETGEAR-router-using-TFTP-client
  14. R

    Kamoj Kamoj add-on V5 for Netgear R7800 X4S and R9000 X10

    It may well be that the issue is with the netgear code and just manifests itself when using the add-on. I will take that advice for now and see if anything changes with the next version of the add-on.
  15. R

    R7800 Return to Stock

    Thank you @kamoj. My understanding is that the nvram command only affects the router settings. Is it the "mtd erase netgear" that will remove any installed software/packages? I have seen this command mentioned in association with people having trouble with the radios. My radios are working fine...
See more
Top