Recent content by rmann2020

Gocoax adapters continue working until step 9 when i rebooted them. At that point, the whole home pvr became active and the gocoax adapters wouldn't work again until I disconnected the nextboxes. @gocoax hoping you can jump in to provide insight and direction. Thanks.

Based on the advice of @Datalink (another forum), I decided to do one more set of tests. This time, I moved both gocoax adapters and the nextbox devices to the same room to ensure an in-wall splitter (which may or may not exist without my knowledge) may be causing the issue. When the Nextbox...

I finally had a chance to continue testing today and tried to go step by step to see where things go wrong. From what I can gather, it appears that the Gocoax and Whole Home PVR cannot work together. Hoping someone can offer some advice as I'd really like to keep my whole home pvr...

I assumed I only needed one-way from basement to 2nd floor where my wifi access point will be ceiling mounted.

Option 2 did't work for me. I ended up ordering a 5 port moca amplifier splitter (https://www.ppc-online.com/5-and-9-port-active-return-moca-enabled-coax-amplifier-splitter) in hopes that it may help. Just waiting on it to be delivered and will post back my results thereafter.

@Booboo22 - I am doing my best to follow the advise and posted step by step tests so that I don't go to far before getting feedback on changes I'm seeing. Each night when I'm done testing, I have to restore back to ensure the TV is working properly upstairs. As I mentioned in my first post...

Should I keep D-Low and D-High checked as well? ... or just D-Ext? Also, should LOF stay at 1400 or change to a different value?

I don't think there are any devices working between 1125-1675MHz. Prior to receiving the gocoax adapters, I only had a 5-1005MHz splitter and the Whole Home PVR (MoCA 1.0/1.1) was working correctly. I have since purchased replaced with the splitters shown in the diagram below.

LOF is now set to 1400 with only D-High band checked for both adapters. Nextbox Whole Home PVR is now working, but stability has started decreasing as I noticed a few disconnects. I'm starting to see RX Bad/Dropped #s above zero whereas when I had LOF = 1150 and all Bands checked it very...

My power went out for a minute this morning so both adapters power cycled at the same time. To my surprise, they both stated working when they came back online. Both adapters have all 3 bands checked and are fully connected to all planned splitters. PHY Rates are strong as per below. Should...

I have not seen any other wallplates in the house and, to the best of my knowledge, it's just the 4 drops. That said, I clued into the fact today the the color cable in the basement is different than the color cable in both the main floor and second floor which is why I suspect splitter(s) in...

No splitters are being used currently.. still connecting the adapters directly. Edit: unless there's a splitter in the wall which I'm not aware of... which may likely be the case Edit 2: I am now fairly certain that there are splitters in the wall. Now I have to figure out if it's possible to...

Update: I went back to stock settings with no security enabled and connected the adapters directly (using coax from basement to second floor). Everything worked perfectly with expected PHY Rates. I then updated both adapters to D-High only and PHY dropper to ~700. Is this expected? I'll...

What LOF do you recommend for D-High band? For security settings, should I also use D-High or stick to D-Ext? Isn't that what I did in Test 1-3 (MoCA adapters connected directly) and then Test 4 (2 way splitter added on second floor only)? Test 4 is when the adapters wouldn't reconnect and...

Just following up to see if anyone has any advice or guidance to share about my posted results. Thanks