Recent content by Shonk

I find it odd that this isnt supported in the ui yet when most isp's support it and the hardware also supports it its a super simple win to just allow 1500/1508 to be set in the ui 2 second fix Will be setting this when i go PPPOE from IPOE when i change to 1.8gbps from 900mbit next week

Its a hidden ssid not "strange ssid" also the mac address is the same as the main ssid but one digit off xx:xx:xx:xx:xa vs xx:xx:xx:xx:xb for example

It shouldnt be my GT-AX6000 has WPA3 enabled in AP mode and isnt broadcasting a hidden ssid on both frequency's like the BE88U is

Did anyone ever find a way to disable it on the BE88U I have a BE88U as my router and a GT-AX6000 in ap mode and have just noticed the BE88U is running 2 hidden wireless networks

All of the older devices i checked had 100K writes SPI-NOR If my RT-BE88U has SLC Nand it should be much faster booting which its not it takes an actual age i have to wait to 100% then about 20 seconds

Yeah i know it's not merged into the merlin webui yet but didnt notice it in asus firmware i rolled back to asus yesterday for a hour or two to verify asus is just using nvram set jumbo_frame_enable=1 which can be confirmed by checking the webui after applying the nvram value and rebooting I...

Can confirm 10Gbps SFP+ LC-LC SM 10KM Optics jumbo frames 9014 works fine 9.92 Gbps Payload (Will be replacing with a 2.5M DAC in a few days) 10Gbps RJ45 port also fine 9.92 Gbps Payload 2.5Gbps ports also fine 2.48 Gbps Payload 1Gbps ports i have no need to test them but presume they are fine

"none of them need Jumbo Frames for optimal performance" Not true yes you will get 10 Gbps of throughput with 1514 Frames you will also get 10 Gbps of throughput with 9014 Frames But your payload will be alot lower Frame Size 1514 = 9.41 Gbps Payload "not optimal performance" Frame Size 9014 =...

thanks hope it works on SFP+ i have done it but cant reboot the router for a few hours to test I really dont understand why its not maxed out from asus already thats how switches are supposed to be configured its just a setting of the max accepted frame size it doesnt dictate anything to other...

I picked up a RT-BE88U today and noticed a typo or formatting bug in 3006.102.4 in Dual Wan if 2.5G WAN/LAN1 is used for wan (its shows correct if 10G WAN/LAN is used) Jut passing it on for merlin clearly not high priority

Just ordered one for £259.. i did order a RT-BE92U first for £169 but decided to go with hardware spec over 6ghz Retiring RT-AC88U 160Mhz revision (AP Mode) GT-AX6000 going to be used as AP to replace above (currently primary router) RT-BE88U going to be primary router Has anyone got any...

I did this and Aurora RGB is still on 1. Enable LEDs. 2. Set Aurora RGB Enabled 3. Disable LEDs. Aurora RGB is locked to off but its still on

Yes Yes they are :)

Reboot didnt do anything Upgrade to 388.2_Beta 1 didnt do anything Factory Default worked fine (even after disabling it and reboot) Restore my Config its broken again Seems its a quirk of my config Im going to have to manually backup all of my settings and factory default it does anyone know...

Router Model Affected Models: GT-AX6000 Firmware Version Affected 388.1 Describe the bug I disabled Aurora RGB a while ago and tried to re enable it today The button doesnt seem to be working (Tested Firefox + Chrome) Expected behavior When i press the slider it enables Aurora RGB