Menu
What's new
By:
Filters Better Search

Recent content by Sneakytiki

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    I don’t think it’s a bug, some type of stability and improvement like with when my devices were bouncing between node and router because of interference until I moved the node. Mostly posting for informational purposes so if people have similar issues maybe something I did will help. The only...
  2. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    Yes it never went that high on the AC3100. It still used 80 on both its back haul and the network. I could still set the primary router on 160 though. Which I did at 36 and 160 so there would not be any issues. Since the rest of the network would be fine and we only have a couple laptops that...
  3. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    That might be the only error I have not been getting, I did get it when I first did a dirty upgrade, also got some type of FPM broadcom errors. I got rid of diversion and did a complete reset with some other network updates and no longer see the message. I run AIProtection, Adguard, Skynet (may...
  4. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    I got 386.7 working on my AX88U. I could not use WAN Aggregation to get up to 2Gbps and I could never have set up an AIMesh with my AC3100. Full reset, no AIMesh with the 3100 worked. AI Mesh and gutting removing the node did not work. I also disabled ipv6, no idea if that made a difference...
  5. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    Mine says 63, with only 5 MB used. I wiped it a few days ago when I factory reset the router to try and get this firmware to work.
  6. S

    AdGuardHome [RELEASE] Asuswrt-Merlin-AdGuardHome-Installer (AMAGHI)

    If it helps, I just swapped Diversion for AdGuard because I use TrendMicro and Adaptive/Flex QoS and was having issues on my AX88U upgrading to beta and the new merlin firmware. Those issues seem unrelated though. Blocking the exact same stuff with some basic testing, also works well with...
  7. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    Yes, I did see some issues with that when I was searching through the site, it was definitely on my list with the firmware upgrade. We rebuilt the entire network, new name, new passwords, default settings, just merlin on the router and it was still having issues. I do want to try AdGuard on the...
  8. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    Firmware on nodes (AC3100) did not make a difference and aggregation is between modem (CM1150V) and router (AX88U) only. It either sits there attempting to get an address and then reboots or stalls with an error (DHCP) or it says network cable disconnected. Ethernet cable or wireless mesh did...
  9. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    Yeah, no worries, its always a blast trying to figure out the primary cause of something. Aggregation is the issue with most of the problems, at least I think it is. There is something wonky with wireless and ethernet at times too, especially with 160mhz and maybe full ethernet speeds, but its...
  10. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    Tried flashing 386.7 again on AX88U and it broke it. Even tried fresh one more time, no add ons, let it sit , no USB drive, overnight. On an AX88U with AIMesh, IPV4/IPV6 (disabling IPV6 was also a no go with WAN Agg), and with WAN Aggregation (disabling it works), Comcast 1200/50 w/ Netgear...
  11. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    386.5_2 reflash gets me WAN Aggregation and 160Mhz back, plus much faster and reliable connection to cable modem which is a Netgear CM1150V, seconds instead of minutes. WIFI drops stopped, authentication errors stopped, network cable and ethernet cable disconnects stopped, other weird errors are...
  12. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    Yep, plus it’s AT season in my area and quite a bit of aircraft this year. 80 seems fine, don’t really notice a performance difference but I do like it when certain devices connect and it jumps 160. Helps when moving large files and downloading stuff from work and games. Which it does on the...
  13. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    That’s where it is for now. Just not sure what changed with the update, no interference, no radar, nothing. It’s been there for a couple years. It won’t even clear the channel for radar or whatever and won’t let me select channels on any of them. Auto is the only option. I’ll look through it...
  14. S

    Release Asuswrt-Merlin 386.7 is now available for all models

    I do not post often - no need, everything is usually great and I've been dirty upgrading all year. This time - my AX88U did not like it. Beta 1 was fine, Beta 2 started having intermittent client drops and radio cycling. Then this one completely borked my network. 50 Devices - Mesh with...
  15. S

    [ 386.4 alpha Build(s) ] Testing available build(s)

    For the USB drive? No, I take it to my laptop, format, take it back to the factory reset (using the WPS key) router, then set up the drive again in amtm when I’m ready. Then I start over, building to my previous settings that were stable over about a week or two. It’s been a few months since...
See more
Top