Recent content by StrikerXXX

I updated my ac68u to this version, until now working well, without errors.

Guys, how do you definitely disable this message? I do not use wifi from the router, I have our own for this, functioning as an access point, but this message bothers me. Is it possible to disable it?

Yeah, I did the installation of the fresh tomato by web gui. But first, I returned to the official firmware of the asuswrt, the build RT-AC68U_3.0.0.4_386_51722-g6b920b0, after already having the official firmware, I did the update to the fresh tomato via web gui. Then I made the following...

I did this, I reinstalled merlin, disabled any means that left the router unsafe, such as remote access, telnet, ssh and etc. I also turned off the wireless part and everything related to it, because I will not use it, this is the responsibility of the other router that I use as an access point...

Guys, I'd like to thank everyone for the tips, even if late. Now with the end of the merlin stand, I am no longer using the merlin firmware, I have the fresh tomato installed. Using the nextdns in it is a bit more annoying to configure, but it is easy, here's the link how to configure for those...

Unfortunately I still need to keep using my asus ac68u v3, I still can not buy another router now. Routers of the asus in my country cost a small fortune, so not to get an outdated firmware, I decided to install the fresh tomato in place of the merlin, it is decent, it works well in ac68u. In...

Guys, in January I will change my ac68u v3 permanently, still not sure what I will buy, but it will be something like Mikrotik HAP AX2 up, the wifi part probably acquire some unifi wifi 6 or 7, they are responsible for the wifi connection. Meanwhile, I want to reduce the load on top of ac68u as...

Speaking of CLI installation, what are the differences between dns over https and dns over tls in the nextdns? Which of the two protocols is more secure, stable? I know that the installation in cli is DoH, the configuration in dot can only do it by the merlin webgui.

Something I notice is that using the nextdns with the dns over tls really the connection with the sites takes a little longer, it should be by the question of crypto, correct? Using dns over htps is faster. I also have these doubts: AsusFreak, I would also like to know what to do in this...

It is configured as in its example, the DoT is functional. Is Doh better than dot? I always doubt what would be better than the two protocols to use.

Guys, I'm using nextdns in merlin, but I would like to know the correct form of nextdns configuration. This is the configuration I use: Is this the correct way to set up nextdns in merlin right now? In nextdns panel control, what should I set up to get the most out of the merlin? I did the...

I finally managed to resolve the issue of the ntp service not working: for some reason, ntp servers in the ipv4 standard do not work, I believe it is due to some configuration that my internet provider implements. I decided to only use ntp servers on both the primary and secondary in merlin in...

The ISP device is in router mode, it is making the PPPoE connection, the ac68u is in AC mode. I tried to activate the same ntp server on both, isp device and the ac68u, unfortunately the ac68u still does not synchronize the ntp. I also tested configuring the ISP device in bridge mode and the...

The LAN1 port of the ONT is connected to the WAN port of the AC68U. At the moment the ac68u is in ac mode, I have already tested with the ont in routed mode and using the ac68u in dhcp mode, the ntp service continues without synchronizing. My pc is connected to the ac68u's lan1 port.

The ont was installed and configured in router mode, I used my ac68u in ac mode. The ac68u's ntp service does not work, both in ac and dhcp mode. On ont, the ntp service works normally, its date and time works without problems. At the moment, I configured the ont for bridge mode and the ac68u...