• SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by toaruScar

  1. toaruScar

    More than one DDNS

    Why not just use the CNAME entry?
  2. toaruScar

    amtm amtm won't start

    Ok fixed with mv /opt/bin/curl /opt/bin/curl.old
  3. toaruScar

    amtm amtm won't start

    In my case the storage is not in RO. It got stuck on this command: /opt/bin/curl -fsNL --connect-timeout 10 --retry 3 --max-time 12 https://diversion.ch/amtm_fw/swap.mod -o /jffs/addons/amtm/swap.mod.new When adding the verbose flag, I got the follwoing: /opt/bin/curl -vfsNL --connect-timeout...
  4. toaruScar

    amtm amtm won't start

    My amtm won't start after updating to 6.0.1 after running amtm, all I see is just amtm 6.0.1 by thelonelycoder RT-AX88U (aarch64) Kernel-4.1.51 FW-3004.388.9_2 @ 192.168.50.1 Operation Mode: Wireless router Sat Jun 28 14:10:32 DST 2025 amtm - the Asuswrt-Merlin Terminal...
  5. toaruScar

    AiMesh reports a PHY rate of 1000+ Mbps, while iperf3 gets only 350 Mbps?

    Thanks for the tips! I checked again, and they are indeed on recommended 5GHz-2 that's reserved for backhaul.
  6. toaruScar

    AiMesh reports a PHY rate of 1000+ Mbps, while iperf3 gets only 350 Mbps?

    I have installed ZenWiFi XT8s on Merlin firmware. The AiMesh pages indicate that the wireless backhaul has a PHY rate of 1441 Mbps. However, when I run iperf3 between these two routers, it achieves only 350 Mbps. On the wireless log page, the utilization jumps to 80% during the iperf3 session...
  7. toaruScar

    My trusty RT-AX82U seems to be crashing daily

    My ZenWiFi XT8 has also been experiencing daily crashes recently. Half of the crashes were due to a hung task of wred. I have withdrawn my privacy consent, so there is no longer any wred processes. I will report back if this helps with the issue I am having.
  8. toaruScar

    FlexQoS FlexQOS Packet classification

    It seems to me that according to your methodology, Flow Cache needs to be disabled for iptable rules to take effect. Unfortunately, this is inconvenient because I have a download speed of 500Mb/s but only 50Mb/s upload speed.
  9. toaruScar

    FlexQoS FlexQOS Packet classification

    Correct me if I'm wrong, I think one way to verify this, is to compare the Application column on Classification tab, against the Application column on FlexQoS tab. If they're diferent, then it means iptable rules is not effective? Like in the example below, I had a iptable rule to classify...
  10. toaruScar

    FlexQoS FlexQOS Packet classification

    I'm using Zen WiFi XT8, the kernel version is 4.1.52, so it's HND5.02. But since it's an XT model, it's also affected? So I need to disable HW acceleration if I want to use IP table rules.
  11. toaruScar

    FlexQoS FlexQOS Packet classification

    Hi, do you know how to check if a router is too new for iptable rules? Thanks in advance.
  12. toaruScar

    BACKUPMON How to run backup if I don't have a source Ext USB drive?

    Ok I figure out one workaround is to mkdir "/mnt/<selectusbdrive>" But this is just too stupid...
  13. toaruScar

    BACKUPMON How to run backup if I don't have a source Ext USB drive?

    This seems to be dumb question, but I can't figure out how to configure backupmon if I just want to back up my JFFS and NVRAM to a network SMB drive. This is for a satellite AiMesh node and there's no USB attached storage.
  14. toaruScar

    Time machine disk not found

    https://www.snbforums.com/threads/mdns-name-drifting-on-zenwifi-xt8.64295/ Check if the router has changed its mDNS name because of a "conflict".
  15. toaruScar

    Zen WiFi X8 reset itself overnight. Can I retrive some old settings?

    Wired, because all the script and device icons are also gone.
Back
Top