Menu
What's new
By:
Filters Better Search

Recent content by trpltongue

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. T

    Home Network Design help with L3 Switch

    Thanks!!!! Will do. So far, everything is working well. But I do want some runtime, because in the past, the ATT system had to get rebooted every now and then because the Cisco router would lose its internet connectivity. The ATT side would work fine, but just the Cisco side would drop...
  2. T

    Home Network Design help with L3 Switch

    Thanks! 12 hours later and everything is still stable, using the router IP as the DNS for my static IPv4 reservations.... :)
  3. T

    Home Network Design help with L3 Switch

    Factory reset complete and everything is back up and running :) When you say you set your laptops dns to 192.168.10.1, you mean in the wireless adapter settings? Or in the SG-300? I've changed it to my router IP on one of my static routes and it seems to be working so far! I'm going to give...
  4. T

    Home Network Design help with L3 Switch

    I did setup the router with 9.9.9.9 and set the VLANs and WAP's to use the router IP 192.168.10.1, but it never worked. It only worked if I used the outside DNS. Hey, when you mentioned the "from scratch" setup of the router, what did that entail? A full factory reset?
  5. T

    Home Network Design help with L3 Switch

    WOOT!!! I think the DNS IP address was the problem! I had left that option as "none" in my static IP reservation page. Changed it to 9.9.9.9 and now it works perfect! At some point I'd like to understand that whole thing better. I'm not sure why I am relying on an outside DNS? But I don't...
  6. T

    Home Network Design help with L3 Switch

    Everything is working fine if I don't set a static IP. We got the main VLAN1 and guest VLAN2 complete. It's been running perfectly. I'm just ready to move forward and convert all devices over now :) If you've got screenshots related to DHCP reservations, I would definitely appreciate that...
  7. T

    Home Network Design help with L3 Switch

    I'm running WAP581's. I wasn't sure if there was some way to define the network name being broadcast, but sounds like it's a windows thing I can't change. The wifi devices obviously pick up the SSID, but the wired devices just get a boring generic name :) Yeah, I'm trying to assign DHCP...
  8. T

    Home Network Design help with L3 Switch

    So.....back again finally :) I've been running this setup in parallel to my ATT setup and it's been working well. Yesterday I moved all the hardwired devices over to the Cisco stack and I'm slowly working through the wireless devices. As a quick reminder, I've got the Cisco RV340 running at...
  9. T

    Home Network Design help with L3 Switch

    Thanks! I’m going to try to take some time to understand that video :)
  10. T

    Home Network Design help with L3 Switch

    Awesome! I’ve been running for a few days now without any issue. I had a bit of a hiccup with the ATT gateway and needed to reboot it, but it’s been running for a week now in parallel with the normal system with no issues. I’ve been swamped with work lately so I haven’t had a chance to think...
  11. T

    Home Network Design help with L3 Switch

    I have disabled the 2.4Ghz on the Cisco WAP for now and disabled the 5ghz on the att WiFi. I am running the att gateway in passthrough mode, but dhcp is still enabled on the att gateway and all my other gear is still connected to it. Apparently the gateway runs in a bit of a dual mode where it...
  12. T

    Home Network Design help with L3 Switch

    It was running perfectly when I had the laptop connected via wire directly to the switch on an access port. In the long run, I will run it from my server directly connected to the switch, but for now I’m running the Cisco gear in parallel to my ATT network and using my laptop and iPhone to test.
  13. T

    Home Network Design help with L3 Switch

    It’s running on my laptop connected to the main WiFi on the WAP581.
  14. T

    Home Network Design help with L3 Switch

    I’ll try to do some throughout tests tonight. On a different note, I keep getting the following error when running FindIT: As soon as I click a button (yes or no) the FindIT box goes blank and I can’t see any devices. I can logon to the switch network manager and see them, but not through...
  15. T

    Home Network Design help with L3 Switch

    Got the second WAP installed as mentioned. Pretty easy. Just had to login and change the name. Regarding LAG, I don’t know that I’ll need more than 1gbps but I’ve got the cables already run.... Seriously though, I would like to be able to stream Blu-ray rips in full quality without any...
See more
Top