What's new
By:

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by xptopt

  1. X

    Question about Trend Micro Signature "update failed"

    Hi when i run "sh -x /usr/sbin/sig_update.sh" i get this + wget_options=-q -t 2 -T 30 --no-check-certificate + nvram set sig_state_update=0 + nvram set sig_state_flag=0 + nvram set sig_state_error=0 + + grep -i nt_center nvram get rc_support + IS_SUPPORT_NOTIFICATION_CENTER= + [ != ] + nvram...
  2. X

    Asus ac66u lan only 100mbps

    That was reported to me by one person on my isp forum, he had the same problem on the last beta from Asus with the meo ISP profile. I recommended Merlin 378_56 to him but now that you report the problem on this to i assume that we need to w8 for Asus or Merlin to find the problem source.
  3. X

    Asuswrt-Merlin 378.56 is available

    2 RT-AC87 with with 378.56_1 different nat loopback results Whit different ISP´s one works with Merlin option the other only with Asus
  4. X

    Asuswrt-Merlin 378.56 is available

    Yes also on 378.56, ill send you the log in a few minutes.
  5. X

    Asuswrt-Merlin 378.56 is available

    hi, i have the same problem on my RT-AC87 i tested with the Meo profile and the manual configuration but get no wan IP. I checked the vlan config and ports with robocfg show and it's all like it should be . Note.. It's working correctly on my AC-3200
  6. X

    [Fork] Asuswrt-Merlin 374.43 LTS releases (Archive)

    hi I have figuredout my problem, the symptom was exactly the same of the DSCP bug , so a assumed that my isp had messed up the DSCP. But in the end i was causing the problem, i was Short on sapace on my desk so i placed my RT-N16 on top of a CRT Television, MY bad :( , and this make the router...
  7. X

    [Fork] Asuswrt-Merlin 374.43 LTS releases (Archive)

    Hi @john9527 I have installed your last version to test the DSCP fix on my RT-N16 since my isp causes the same issue as Comcast (MEO isp from Portugal) The fix have not worked for me , and disabling WMM is not doing the trick either with build 374.43_2-13E1j9527. The tomato fix Works very...
  8. X

    Asuswrt-Merlin 378.52 is available

    Strange behaviour on RT-AC87U with vlan + bridge i'm testing my isp new fiber service that uses single edge IPOE , the service uses VLAN12 for all serviçes Internet iptv and voip. But since my isp doesn't provide me the voip credentials , i need to bridge port 4 to vlan 12 , and connect...
  9. X

    vlan IPTV + internet help

    hi that's what i have done , the problem is Vlan 12 have no internet. on my isp router i have all lan ports with internet and iptv , im trying to do the same on the asus on port 4 Thanks
  10. X

    vlan IPTV + internet help

    Hi my isp uses pppoe with Vlan 10 for internet and Vlan 12 for IPTV, everything works except the interactive services on my STB , for this to work i need to have internet on Vlan12 port 4. this is the switch configuration. 1: vlan1: 1 2 3 8t 2: vlan2: 0 8u 10: vlan10: 0t 8t 12: vlan12: 0t...
  11. X

    Asus RT-N66U - Using VLAN = LAN3 + LAN4 stop working?

    set switch_stb_x=0 puts port 3 and 4 on the same vlan as 1 and 2 , by default the firmware puts lan tag port 3 and 4 if value is left empty to vid 6 but to use port 3 or 4 as lan the value should be 0 try this, after config the iptv vid use only this command nvram set...
  12. X

    Asus RT-N66U - Using VLAN = LAN3 + LAN4 stop working?

    after you use the commands and set port 4 to VID 845, port 3 should work as normal lan i think ,just leave port 3 VID blank . Or try this nvram set switch_stb_x=0 nvram set switch_wan1tagid=845 nvram set switch_wan2tagid=0 nvram commit reboot don't know if it works but you can...
  13. X

    Asus RT-N66U - Using VLAN = LAN3 + LAN4 stop working?

    Hi I have the same problem , need to use VID 10 to the internet service and let port 3 and 4 on normal lan. There’s any telnet command on merlin builds that can fix this problem . Many thanks Edit Thanks to Merlin the problem can simply be fixed with this telnet commands...
See more
Back
Top
✖