Recent content by Yakumo

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. Y

    FlexQoS FlexQoS issues with 388.4 HND5.04 models

    > nvram show 2>/dev/null | grep -E "=ptm0$" wan_ifnames=ptm0
  2. Y

    FlexQoS FlexQoS issues with 388.4 HND5.04 models

    > nvram get wan_ifname eth4 > cat /sys/module/tdts_udb/parameters/qos_wan ptm0 > tc qdisc ls | grep -v br0 | grep root | grep htb qdisc htb 1: dev ptm0 root refcnt 2 r2q 10 default 0 direct_packets_stat 32 direct_qlen 1000 All I have done on this router since clean installing the current...
  3. Y

    FlexQoS FlexQoS issues with 388.4 HND5.04 models

    I'm getting no upload data in the graphs for either the Classification page under Adaptive QoS, or on the FlexQOS v1.3.5 page. I'm not sure when this started to happen I do know I have observed that data on the flexQoS page in the past when I was tuning FlexQOS bandwidth. On the FlexQoS page...
  4. Y

    FlexQoS FlexQoS issues with 388.4 HND5.04 models

    The most detailed info is probably still here, n the first few posts and in the spoiler sections you have to click to open too https://www.snbforums.com/threads/release-freshjr-adaptive-qos-improvements-custom-rules-and-inner-workings.36836/
  5. Y

    CakeQOS CakeQoS-Merlin v2.1.1

    I chanced upon this wanting to check what the diffserv8 tins were designated for, this answers that and more so I thought it should be posted here as generally useful information there is some info that might help those trying to manage wireguard too...
  6. Y

    FlexQoS FlexQoS issues with 388.4 HND5.04 models

    38 minutes after your post, neither amtm nor the update button in the script's configuration menu offer an update/hotfix. Edit: ran the flexQOS CLI through amtm, told it to update anyway after it reported none and that has worked, ipv6 enabled and data in the correct columns and filtering...
  7. Y

    FlexQoS FlexQoS issues with 388.4 HND5.04 models

    # nvram get ipv6_service dhcp6 nvram get ipv6_prefix - returns nothing, it just skips a console line and exits. Edit: Disabling ipv6 does end this behaviour, the data starts and stays is in the correct columns, filtering doesn't result in the data vanishing on the first autorefresh
  8. Y

    FlexQoS FlexQoS issues with 388.4 HND5.04 models

    I noticed this about 20 minutes after installing via amtm, only a few minutes before posting. IPv6 was enabled on the router but I don't have a WAN ipv6 IP still as vodafone is doing a very slow roll out. You have to switch to Automatic QoS before amtm will install flex, but I didn't run the...
  9. Y

    FlexQoS FlexQoS issues with 388.4 HND5.04 models

    Trying FlexQoS again on a DSL-AX82U with 3004.388.5_0-gnuton1 firmware , amtm installed FlexQoS v1.3.5 when I first go to the FlexQoS page in the Tracked Connections table the Local IP and Remote IP columns is populated the wrong way round, if I enter a filter then the new data is the correct...
  10. Y

    CakeQOS CakeQoS-Merlin v2.1.1

    No, but that's why I said I was interested in what it could do on traffic load. I play UDP based games that are very sensitive to any jitter or any fluctuations and have found different settings give the most responsive play in different circumstances so I wanted to tinker with your script and...
  11. Y

    CakeQOS CakeQoS-Merlin v2.1.1

    DSL-ax82u, and I'm already using CakeQoS-Merlin v2.1.2, I was interested in testing the automatic change on traffic load from the autorotate script.
  12. Y

    CakeQOS CakeQoS-Merlin v2.1.1

    It would be great if there was any possibility this could be run without needing a USB drive, I use the USB port to power a Ubiquiti USW-Flex
  13. Y

    CakeQOS CakeQoS-Merlin v2.1.1

    @dave14305 I've just seen a post from last year saying you're using qosify now, is that still the case? Is that usable on Merlin?
  14. Y

    Beta [FORK] [DSL] [TESTERS] GNUton's Alpha/Beta Merlin builds

    I see an upcoming change with 3004.388.5 builds is: - CHANGED: Display tracked connections on the QoS/Classification page even if QoS isn't set to Adaptive QoS. Does this impact CPU or other resources when not looking at that page? If so will there be an option to turn off that data gathering?
  15. Y

    CakeQOS CakeQoS-Merlin v2.1.1

    Isn't the egress default dual-srchost that incorporates flows superior?
Top