gnuton

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. E

    Cannot flash DSL-AX82U with GNUton firmware

    Hello I have a DSL-AX82U with the the latest ASUS firmware (3.0.0.4.388_23756-gc732440). I have been trying to flash to the latest GNUton firmware (DSL-AX82U_3004_388.6_0-gnuton1_puresqubi.w) but without success. Everything seems to go to plan; the new firmware takes a couple of minutes to...
  2. P

    ASUS ZenWifi ET8 GNUton Firmware question

    Hi. I am considering getting an ASUS ZenWiFi ET8 mesh system to upgrade from my stand-alone RT-AC86U router. However, I saw that it does not support IPTV, but I wonder if the GNUton firmware does. I need the IPTV to set the VLAN to 201 so I can bridge into Centurylink Fiber without using their...
  3. davidski

    GNUton 388.2 - ZenWifi XT8 - avahi name conflicts

    I'm running three ZenWifi XT8s (HW Rev 1.0), all interconnected over Ethernet. The primary node is running GNUton's 388.2 fork, while the two mesh nodes are running the latest ASUS stock firmware. The main node and one mesh works fine, but the third device (running in mesh) has been nothing but...
  4. _BLACK_BuLLeT_

    How to limit the speed of a specific site on ASUS TUF-AX5400?

    There is an ASUS TUF-AX5400 router with the latest Merlin (388.2_2_0-gnuton1) firmware. How can I limit the speed of downloading data from a specific site (or at least from several IP addresses) on this router? I do not need to limit the speed of the entire specific device. I also do not need to...
  5. Sp0X

    Will 388.2 be on the AX-5400?

    Hello @RMerlin . Will there be an adaptation of 388.2 for the AX-5400? As I understand it, the AX-5400 in terms of components is a copy of the RT-AX58. Previously, the fork was done by @GNUton , but the last time he visited the forum was in February and now he is not active either here or on...
  6. Sp0X

    Low wan speed with VPN director enabled

    Hello everyone. Forgive me for possible errors in the text, I write through a translator. A question arose about the work of the VPN Director. There are no errors in the logic of its operation, the traffic is redirected as it should. But the speed of WAN, which is the Internet not through a VPN...
  7. F

    Tutorial Setup the ASUS TUF Gaming AX5400 router for Transmission with remote access using an SSD for storage

    Hi Everyone, I post this tutorial because I found the infos regarding the subject too scattered on the net. Some of the info is not even out there or not easy to find at all. I hope you will find this helpful. Feel free to comment if there is anyhing important to add. In order to succcesfully...
  8. I

    Issues adding node (DSL-AC68U)

    Hi there, long time lurker, first time poster. I've got a multi-node ai-mesh setup, which until recently has been running fine. I started having issues with a specific node dropping off and needing re-added to the system, it's a DSL-AC68U, although obviously not being used as a modem, just an...
  9. P

    Username and Password invalid when trying to access AiMesh Nodes

    Hi all, I am using an RT-AC86U running Merlin 386.5_2 as my AiMesh router and 2 x DSL-AC68U's running 386.5_2-gnuton0 as AiMesh nodes. They work absolutely fine however since upgrading them all to the latest respective releases I am no longer able to log in to either node to change any...
  10. GNUton

    [FORK] [DSL/RT] GNUton's Asuswrt-Merlin builds

    Hi, Aim of this project is to provide SW and support for the following models: DSL-AC68U DSL-AX82U RT-AX82U TUF-AX5400 TUF-AX300 ZenWifi XT8 This is an official Merlin fork and it's supported by @RMerlin and Asus. Code and more info are available here. For support please use one of the...
Top