What's new

Issues with Verizon CR1000B, Hitron MoCA HT-EM5 adpaters, and Netgear RAX70

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

dansmith2401

New Around Here
Hi, I've posted this across multiple different internet forums but had no luck and am hoping for different results here at SNB.

Basically I have Verizon Fios with their given CR1000B router, and from that, I have both the coax port going through a splitter (2.5 GHz 5-2500 MHz rated but no terminator caps on the unused ports and a POE filter on the incoming signal but we only have internet) that are then connected to a Hitron HT-EM5 2.5G adapter. This adapter is then connected to an unmanaged Netgear gigabit switch, which then connects to a PC, Xbox, and PS5.

On the other end of the router, I have a Netgear RAX70 connected via Ethernet which is then set up in AP mode. On this Rax70 I have a PC and a JBL soundbar both hardwired. I also throughout both routers have a multitude of wireless devices (IoT, Phones, Tablets, Chromecasts, etc) Diagram is included below.

The issue I have is that when the RAX70 is in AP mode the PC connected to the MoCA adapter intermittently loses internet connection. Now, it doesn't just lose internet connection, the device adapter itself says that there's no ethernet connection period. As in, the same status as there being no cable inserted into the adapter. Now, when the PC connected to the RAX70 is off, however, this does not occur. Furthermore, when we turn the RAX70 into router mode and have 2 networks with a double NAT etc, this issue also does not occur.

I have tried troubleshooting this in multiple ways, seeing if there are IP conflicts, wiring issues, etc. I have even connected the PC to the MoCA adapter directly without the network switch, but nothing seems to work and I can't id the problem. I have used Wireshark, and nothing in Wireshark on both computers would give me any indication of a problem. I have tried getting new DHCP IP4 addresses, every possible combination of CMD commands (ipconfig), Powershell (winsh), you name it. I am honestly at my wit's end here.

I don't think it's a hardware issue, I don't think terminator caps are giving me this issue even if it is best practice. At this point I think it's either a software issue or a networking issue. I haven't connected the two desktops to the same router which could maybe show more, but at the moment that is not possible since I work from home and the other PC user also does a lot of work from their PC. Theoretically, I could just keep this its own separate network, but besides it being an inconvenience, I'm sure most if not everyone on this forum would love to figure this out and get these devices working in their intended manner. If anyone had any tips or pointers, or needs more info (logs, screenshots, etc), would happily provide. This has been killing me and idk know where else to go!
Apartment Network Diagram.png
 
I'm feeling a bit suspicious about using the FiOS router's coax port. I have a CR1000A, which I believe to be substantially the same hardware, and its user manual basically disclaims compatibility with everything:
  • Warning: The coax port is intended for connection to Verizon devices only. It must not be connected to any exterior or interior coaxial wires not designated for Verizon devices.
So what I'd try is getting another ethernet-to-MoCA adapter, plugging that into one of the FiOS router's spare ethernet ports, and using that to drive your MoCA link instead of using the FiOS router's own coax port.

A different line of thought: I imagine you are using the FiOS router's 1/2.5/5/10G port to connect to the RAX70, just because it's there? I had some weird compatibility issues with the 10G port on mine, and eventually stopped using it in favor of the two max-2.5G ethernet ports. It's not like you need any more speed than that for your FiOS connection.

And a third thing: you're evidently not using the FiOS router's wireless access point, but are you sure that's turned off? I found that you had to dig deep into the "advanced" settings to make it really shut off. I'm not sure that having that active could cause your reported problems, but the last thing you need here is any unintended data pathways in your LAN.

(Truth be told, my FiOS router is actually sitting on the shelf at the moment --- I eventually got fed up with it and replaced it with a pfSense router from Netgate. But that was about wanting more configuration control, not because I was still having compatibility issues.)
 

Similar threads

Latest threads

Support SNBForums w/ Amazon

If you'd like to support SNBForums, just use this link and buy anything on Amazon. Thanks!

Sign Up For SNBForums Daily Digest

Get an update of what's new every day delivered to your mailbox. Sign up here!
Top