RBR50 Bricked? U-Boot shows "Nand Flash error. Status = 64"

[scruff67]

Here is what I am seeing in U-Boot on boot:

Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00096
S - IMAGE_VARIANT_STRING=DAAAANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x00000023
S - Core 0 Frequency, 0 MHz
B - 261 - PBL, Start
B - 1339 - bootable_media_detect_entry, Start
B - 118517 - bootable_media_detect_success, Start
B - 118531 - elf_loader_entry, Start
B - 120898 - auth_hash_seg_entry, Start
B - 123045 - auth_hash_seg_exit, Start
B - 157118 - elf_segs_hash_verify_entry, Start
B - 270294 - PBL, End
B - 270319 - SBL1, Start
B - 358794 - pm_device_init, Start
D - 6 - pm_device_init, Delta
B - 360357 - boot_flash_init, Start
D - 595 - boot_flash_init, Delta
B - 367190 - boot_config_data_table_init, Start
D - 75277 - boot_config_data_table_init, Delta - (419 Bytes)
B - 448338 - clock_init, Start
D - 7541 - clock_init, Delta
B - 459302 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1
B - 462783 - sbl1_ddr_set_params, Start
B - 467768 - cpr_init, Start
D - 2 - cpr_init, Delta
B - 472150 - Pre_DDR_clock_init, Start
D - 5 - Pre_DDR_clock_init, Delta
D - 13143 - sbl1_ddr_set_params, Delta
B - 485524 - pm_driver_init, Start
D - 2 - pm_driver_init, Delta
B - 556373 - sbl1_wait_for_ddr_training, Start
D - 27 - sbl1_wait_for_ddr_training, Delta
B - 572700 - Image Load, Start
D - 785192 - QSEE Image Loaded, Delta - (262104 Bytes)
B - 1358397 - Image Load, Start
D - 887 - SEC Image Loaded, Delta - (0 Bytes)
B - 1368240 - Image Load, Start
D - 1185570 - APPSBL Image Loaded, Delta - (413427 Bytes)
B - 2554241 - QSEE Execution, Start
D - 58 - QSEE Execution, Delta
B - 2560508 - SBL1, End
D - 2292179 - SBL1, Delta
S - Flash Throughput, 342 KB/s (675950 Bytes, 1976129 us)
S - DDR Frequency, 672 MHz


U-Boot 2012.07 [Barrier Breaker unknown,unknown] (Jul 29 2016 - 22:37:42)

U-boot dni1 V1.1 for DNI HW ID: 29765352; NOR flash 32MB; EMMC flash 4000MB; RAM 512MB
smem ram ptable found: ver: 1 len: 3
DRAM: 512 MiB
machid : 0x8010001
NAND: Nand Flash error. Status = 64
ONFI Read id cmd failed
ONFI probe failed
SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff
ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)
0 MiB
MMC: qca_mmc: 0
PCI0 Link Intialized
In: serial
Out: serial
Err: serial
machid: 8010001
flash_type: 1
Net: MAC0 addr:a0:04:60:20:e4:aa
PHY ID1: 0x4d
PHY ID2: 0xd0b1
ipq40xx_ess_sw_init done
eth0
(IPQ40xx) # nand info▒
▒*▒ ▒oo ma▒▒▒a▒g▒ (m▒▒▒ %d) ▒*
▒oo▒d▒l▒y▒b▒▒▒▒▒d▒H▒t a▒▒ key ▒▒ߌtop▒▒u▒▒
VV
: %2d
(IPQ40xx) #


Is there any hope, or is this RBR50 done? Go easy on me, I am a complete U-Boot noob.
Thanks for reading, and possibly commenting!