RT-AX92U - How can I measure the router->node (backhaul) connection speed?

Gilad

New Around Here
Hi,
Got the mesh system setup and tweaked the settings and wanted to test the master<->node connection speed.
I tried to ssh but there's no iPerf on neither one and apt-get/yum install seems to be unknown to the shell.

Any ideas/tips on how to measure the backhaul speed?

Thanks!
 

Gilad

New Around Here
Ok, found the solution:
SSH to the node and run:
Code:
iperf3 -s -D
Then SSH to the master and run:
Code:
iperf3 -c 192.168.1.249
Change the IP to the node IP of course :)
 

Smokey613

Senior Member
I just did this.... not sure how good my results are.


Connecting to host 192.168.2.2, port 5201
[ 4] local 192.168.2.1 port 55068 connected to 192.168.2.2 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.01 sec 28.3 MBytes 236 Mbits/sec 3 288 KBytes
[ 4] 1.01-2.00 sec 28.2 MBytes 237 Mbits/sec 1 253 KBytes
[ 4] 2.00-3.01 sec 28.9 MBytes 240 Mbits/sec 1 230 KBytes
[ 4] 3.01-4.01 sec 29.2 MBytes 246 Mbits/sec 0 310 KBytes
[ 4] 4.01-5.01 sec 29.0 MBytes 243 Mbits/sec 2 277 KBytes
[ 4] 5.01-6.00 sec 29.3 MBytes 249 Mbits/sec 0 348 KBytes
[ 4] 6.00-7.01 sec 29.5 MBytes 245 Mbits/sec 0 368 KBytes
[ 4] 7.01-8.01 sec 27.2 MBytes 227 Mbits/sec 14 281 KBytes
[ 4] 8.01-9.02 sec 25.5 MBytes 212 Mbits/sec 0 345 KBytes
[ 4] 9.02-10.01 sec 30.0 MBytes 253 Mbits/sec 0 368 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.01 sec 285 MBytes 239 Mbits/sec 21 sender
[ 4] 0.00-10.01 sec 283 MBytes 237 Mbits/sec receiver
 

Gilad

New Around Here
Mine are a bit higher although on a AX exclusive back-haul (which I have as it's used only for this) , I would expect higher speeds.
I get:

Connecting to host 192.168.1.249, port 5201
[ 4] local 192.168.1.1 port 46880 connected to 192.168.1.249 port 5201
[ ID] Interval Transfer Bandwidth Retr Cwnd
[ 4] 0.00-1.00 sec 66.1 MBytes 553 Mbits/sec 77 427 KBytes
[ 4] 1.00-2.01 sec 72.5 MBytes 606 Mbits/sec 7 387 KBytes
[ 4] 2.01-3.00 sec 72.7 MBytes 611 Mbits/sec 0 513 KBytes
[ 4] 3.00-4.00 sec 68.9 MBytes 578 Mbits/sec 89 238 KBytes
[ 4] 4.00-5.00 sec 56.6 MBytes 476 Mbits/sec 6 297 KBytes
[ 4] 5.00-6.00 sec 60.4 MBytes 506 Mbits/sec 17 365 KBytes
[ 4] 6.00-7.00 sec 67.0 MBytes 563 Mbits/sec 46 390 KBytes
[ 4] 7.00-8.00 sec 74.4 MBytes 622 Mbits/sec 0 518 KBytes
[ 4] 8.00-9.01 sec 73.6 MBytes 617 Mbits/sec 63 324 KBytes
[ 4] 9.01-10.00 sec 71.8 MBytes 603 Mbits/sec 0 467 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Retr
[ 4] 0.00-10.00 sec 684 MBytes 574 Mbits/sec 305 sender
[ 4] 0.00-10.00 sec 681 MBytes 571 Mbits/sec receiver
 

Gilad

New Around Here
So should we run
iperf3 -s (not as a deamon)
On the node and test from the master?
 

ugandy

Senior Member
So should we run
iperf3 -s (not as a deamon)
On the node and test from the master?
i think you should test between 2 clients connected to your nodes. or between client and wan
 

Sign Up For SNBForums Daily Digest

Get an update of what's new every day delivered to your mailbox. Sign up here!
Top