WIRELESS REPORT v1.3.7 - Apr 12, 2026 - WebGUI Table of all connected Client Devices showing RSSI (available in AMTM!)

[JB_1366]

Wireless Report for AiMesh

available in AMTM

Manual Github install link:

curl -sfL --retry 3 https://raw.githubusercontent.com/JB1366/Wireless_Report/main/wirelessreport.sh -o /tmp/wirelessreport.sh && sh /tmp/wirelessreport.sh install

WHAT: Wireless Report gives you an overall snapshot of your wireless network in a sortable/graphical table. The report script installs a tab at the end of the wireless-menu, where you can click headers for sorting/viewing data. a couple of columns are dual viewing, (mac address/ip address) & (SSID/IFACE)

WHY: the reason why I created the script was because ASUS web UI doesn't show AiMesh node information, such as rssi, the main reason I started this, plus its nice to see all wireless devices in one spot. Asus firmware takes way to long to to adjust devices to correct router/node, with the report, I can manually adjust devices easier & faster.

PREREQUISITE: you need to install passwordless SSH to nodes, if one node is detected, script will install, link below:

ASUS-Merlin Router to AIMesh Nodes - SSH Key Setup: Password(#19)-Passwordless(#16) or use Curl(#30)​

NON-PREREQUISITE: but helps with pretty looking HOSTNAMES

YazDHCP - YazDHCP v1.2.5 [2026-Mar-22] - Feature expansion of DHCP assignments (increasing limit on the number of DHCP reservations)​

View attachment 71160
View attachment 71161

any questions, please feel free to reach out.

 

[JGrana]

Github link?

 

[Tech9]

Looking for feedback, the whole purpose for this script was to load balance router/aimesh-node wireless devices. Asus firmware takes way to long to to adjust devices, not to mention after router reboots, node seems lost trying to move devices to correct router/node.

The UI is definitely pretty, but how is the script helping with load balancing? The clients decide where to connect and the reason for the imbalance is the fact AiMesh is multi-AP system with no per device Tx power control. If your nodes are at less than -60/65dBm signal level between them - you're out of luck.

 

[JB_1366]

The UI is definitely pretty, but how is the script helping with load balancing? The clients decide where to connect and the reason for the imbalance is the fact AiMesh is multi-AP system with no per device Tx power control. If your nodes are at less than -60/65dBm signal level between them - you're out of luck.

it lets me see a snapshot, to manually bind devices to where I know they should be, instead of waiting 1 day for fw to try and adjust. as I've been playing around the last couple of weeks, i know exactly where they should be, so after a reboot, i bind them to correct router/node, then I unbind them once they are there..they pretty much stick after that..just being geeky I guess.

 

[visortgw]

it lets me see a snapshot, to manually bind devices to where I know they should be, instead of waiting 1 day for fw to try and adjust. as I've been playing around the last couple of weeks, i know exactly where they should be, so after a reboot, i bind them to correct router/node, then I unbind them once they are there..they pretty much stick after that..just being geeky I guess.

Unless you move devices, why unbind them?

 

[JB_1366]

Unless you move devices, why unbind them?

I find if I keep the bind on, some devices don't like it, and they start greying themselves out in Asus device list, weird i know, so the way I've done it works for me.

 

[Tech9]

to manually bind devices to where I know they should be

I know AiMesh is difficult to tune, but... you have GNP/Network available, no? Make SSID1 at AP1, SSID2 at AP2 and SSID3 at AP1/AP2. Clients moving around connect to SSID3, the rest non moving connect to SSID1 and SSID2 accordingly where they belong to. The moment you turn the routers ON your clients will have no choice but connect to the right APs and you don't have to do anything manually. No script needed.

 

[jksmurf]

Looking for feedback

I think it looks fantastic, I think I’ve mentioned in another thread I have a very crude script that performs a similar function (now run from main, but accesses the nodes) via ssh only.

It shows MAC addresses as well as RSSI numbers, as it’s for troubleshooting like you, but I don’t think your layout has room for that too, if you’d like customization maybe you could have selectable options for what to show / not show.

Mine groups by node similar to yours, but has the devices subgrouped by SSID. I think that would be messy on your screen though.

Other feedback would be does it auto refresh and how long does it take?

But honestly these are minor comments, it is a really nice piece of work, well done to you.

Asus firmware takes way to long to to adjust devices to correct router/node

Yep, all that. I have set in-device RSSI in my Shelly IoT devices which moves them ok and HA recently improved this for ESP32 devices, but you have to be patient.

You could start playing around with RA Roaming Assistant dBm but mine is off for 2.4Ghz anyway; or if I you use Smart Connect, play around with the two settings Trigger and Steering (for each band), but taking that path is like going down a rabbit hole … the cleverer devices like phones will decide themselves anyway.

 

[JB_1366]

I think it looks fantastic, I think I’ve mentioned in another thread I have a very crude script that performs a similar function (now run from main, but accesses the nodes) via ssh only.

It shows MAC addresses as well as RSSI numbers, as it’s for troubleshooting like you, but I don’t think your layout has room for that too, if you’d like customization maybe you could have selectable options for what to show / not show.

Mine groups by node similar to yours, but has the devices subgrouped by SSID. I think that would be messy on your screen though.

Other feedback would be does it auto refresh and how long does it take?

But honestly these are minor comments, it is a really nice piece of, well done you.



Yep, all that. I have set in-device RSSI in my Shelly IoT devices which moves them ok and HA recently improved this for ESP32 devices, but you have to be patient.

You could start playing around with RA Roaming Assistant dBm but mine is off for 2.4Ghz anyway. Or if I you use it with the two settings Trigger and Steering (for each band) in Smart Connect, but taking that path is like going down a rabbit hole … the cleverer devices like phones will decide themselves anyway. default is manual refresh, with 30sec/1min auto refresh.

all columns are sortable, mac/ip-address, ssid/iface columns are toggleable(I had ip-address toggled), so ssid column would group all together per main/node view. default is manual refresh, w/auto refresh selectable of 30sec/1min.

 

[visortgw]

I'd be interested in what I could learn about my network using your script: router, four (4) AiMesh nodes, and roughly ninety (90) clients total.

 

[jksmurf]

I'd be interested in what I could learn about my network using your script: router, four (4) AiMesh nodes, and roughly ninety (90) clients total.

You'll be scrolling for days ....

 

[Tech9]

Where is the script?

The UI is beautiful indeed... for monitoring, for whoever wants to stare at router's GUI. For optimizing AiMesh manually by reconnecting and binding devices to different nodes... the idea was first used in 1878.

 

[CaptainLockness]

will this be added to amtm/addons category soon once released?

 

[Tech9]

will this be added to amtm

There are specific requirements for this to happen.

 

[JB_1366]

curl -sL --retry 3 https://raw.githubusercontent.com/JB1366/Wireless_Report/main/wr_install.sh -o /tmp/wr_install.sh && sh /tmp/wr_install.sh

ASUS-Merlin Router to AIMesh Nodes - SSH Key Setup: Password(#19)-Passwordless(#16) or use Curl(#30)

Im running this script manually on my node, and manually uploading node_upload.txt to my main router. is there a way to automate the process, so i can just run my script on router to use node_upload.txt and apply results? A direct pull of variables would be great, if possible.

www.snbforums.com

YazDHCP - YazDHCP v1.2.5 [2026-Mar-22] - Feature expansion of DHCP assignments (increasing limit on the number of DHCP reservations)

Release Notes for YazDHCP v1.0.8 production version now available [2025-May-29] The fork from @Jack Yaz's repository is now hosted on the AMTM-OSR GitHub repo: https://github.com/AMTM-OSR/YazDHCP 1) FIXED: Errors when loading the webGUI page on the 3006.102.x F/W version. 2) FIXED: Some...

www.snbforums.com

Initial Release - passwordless-SSH to all nodes, are a prerequisite. YazDHCP for pretty Hostnames, not necessary.

 

[jksmurf]

curl -s -L https://raw.githubusercontent.com/JB1366/Wireless_Report/main/wr_install.sh -o /tmp/wr_install.sh && chmod +x /tmp/wr_install.sh && sh /tmp/wr_install.sh

Initial Release

Awesome, will try soon. Before I install it … thinking ahead … in case it goes pear shaped, how do I uninstall it?

Also, if folks haven’t got automatic (no intervention required) login access to nodes it will not show node data, correct? So any install notes would need to clarify this eventually I guess.

 

[JB_1366]

Awesome, will try soon. Before I install it … thinking ahead … in case it goes pear shaped, how do I uninstall it?

there's an uninstall, also helps if your passwordless ssh-keys are all setup, it authenticates before install. and YazDHCP for purty Hostnames

 

[scootertramp]

curl -s -L https://raw.githubusercontent.com/JB1366/Wireless_Report/main/wr_install.sh -o /tmp/wr_install.sh && chmod +x /tmp/wr_install.sh && sh /tmp/wr_install.sh

Initial Release

Any chance you could make the ssh port configurable?

 

[JB_1366]

Any chance you could make the ssh port configurable?

ASUS-Merlin Router to AIMesh Nodes - SSH Key Setup: Password(#19)-Passwordless(#16) or use Curl(#30)

Im running this script manually on my node, and manually uploading node_upload.txt to my main router. is there a way to automate the process, so i can just run my script on router to use node_upload.txt and apply results? A direct pull of variables would be great, if possible.

www.snbforums.com

 

[scootertramp]

ASUS-Merlin Router to AIMesh Nodes - SSH Key Setup: Password(#19)-Passwordless(#16) or use Curl(#30)

Im running this script manually on my node, and manually uploading node_upload.txt to my main router. is there a way to automate the process, so i can just run my script on router to use node_upload.txt and apply results? A direct pull of variables would be great, if possible.

www.snbforums.com

ASUS-Merlin Router to AIMesh Nodes - SSH Key Setup: Password(#19)-Passwordless(#16) or use Curl(#30)

Im running this script manually on my node, and manually uploading node_upload.txt to my main router. is there a way to automate the process, so i can just run my script on router to use node_upload.txt and apply results? A direct pull of variables would be great, if possible.

www.snbforums.com

passwordless is working fine per that post. Your scripts are set-up to use the default port 22.
I do not run on the default port for ssh access. Just looking to see if it could be a configuration option.