Menu
What's new
By:
Filters Better Search

Recent content by ekhoo

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. ekhoo

    Static route on Dlink RG-WBR-2300

    I added on the RV042 LAN 192.168.2.0-192.168.2.255 access to ANY on the WAN side and vice versa - ANY on the WAN side access to 192.168.2.x. Viola! Internet works! I tried the same on the DLink RG-WBR2300 and it works too! Hurray!
  2. ekhoo

    Static route on Dlink RG-WBR-2300

    That sounds plausible. Just after I posted above, I dug around and the RV042G has an option called "Multiple Subnets". When I added 192.168.2.1 to the router, Internet works. So instead of adding this IP thingy, perhaps I can check on the ACLs. And then I'll look at the DLink...
  3. ekhoo

    Static route on Dlink RG-WBR-2300

    192.168.2.112 Client on VLAN2 can't ping beyond the Router (192.168.0.1) 192.168.1.114 client on VLAN1 can ping beyond, i.e. the Internet facing IP (i.e. 124.13.125.242) Something either on the router or the switch isn't right.
  4. ekhoo

    Static route on Dlink RG-WBR-2300

    Ok, rechecked. - Default route on switch is 192.168.1.1. 192.168.1.x network gets Internet. The RV042 is my test router. Production is the D-link. Both configured as 192.168.1.1 (I'm swapping between them for testing). Like you said, "No static for 192.168.1.0" The 192.168.2.x network has no...
  5. ekhoo

    Static route on Dlink RG-WBR-2300

    The RV042G screen above has the route back. If I delete those static routes, the PC loses internet connection.
  6. ekhoo

    Static route on Dlink RG-WBR-2300

    Internet Router is 192.168.1.1 Two VLANS: VLAN1 : 192.168.1.x , Switch is 192.168.1.254 VLAN2: 192.168.2.x, Switch is 192.168.1.254 Switch has DHCP for both on, giving IPs from 1.100 to 1.200 and 2.100 to 2.200. Default gateway is switch ip address. Default route on switch is pointing to...
  7. ekhoo

    Static route on Dlink RG-WBR-2300

    I've a client with the service provider's router: I've configured the switch (SG300-28PP) to do both DHCP and routing from 2 subnets & VLANs. On my test router (Cisco RV042G), I've two static routes to enable internet access: 192.168.1.0/24 --> 192.168.1.254 (Switch IP) 192.168.2.0/24 -->...
  8. ekhoo

    How to setup a Guest network on an Cisco SG300-28 layer 3 switch

    Ah-hah. My bad. Typo'ed the default roues on router. The client (DHCP on switch) default route is correct. 3pm not a very time to configure switches and routers in a cramp closet.... now on to the ACLs! Thanks!!
  9. ekhoo

    How to setup a Guest network on an Cisco SG300-28 layer 3 switch

    Hi Coxhaus, I'm in another state right now and trying to configure the same thing (SG300-28PP) with 3 VLANs and router. For some reason, VLAN 2 and VLAN 10 can't get on the internet. VLAN 1 is fine. Switch is giving IPs. Router 192.168.0.1 Switches are on 192.168.0.254, 192.168.2.254 and...
  10. ekhoo

    Switches that allow the LEDs to be turned off

    On the switches I have (SG300-10PP, SG300-28PP) the option is in both.
  11. ekhoo

    Switches that allow the LEDs to be turned off

    The Sg300 series with the recent firmware has the option of turning off the LEDs. Only the power led is left on.
  12. ekhoo

    VLAN bridging on SG300 series L3 switch

    Yeah, still need the firewall but I thought at least I can have 3 ports on the switch doing the bridging and the RV042 WAN can connect to that particular port with the LAN port connected for the rest of the switch. Right now it looks like this: Fiber BTU --> (Port 1) Mikrotik RB750G (port 2)...
  13. ekhoo

    Vlan Switch Advice

    The SG300 series -- if they don't do POE, they are fanless. The 10-port POE version is fanless as well since the power supply is an external brick. Just checked - SG300-10 (all versions), SG300-20 and SG300-28 are fanless. My SG300-28P has two fans but they seem to throttle base on load. I...
  14. ekhoo

    VLAN bridging on SG300 series L3 switch

    Just checking on the best way to accomplish the following and remove another device off my home network. My home Fiber Internet comes in on VLAN500 (VLAN600 is IPTV). My RV042 Router connects to the Fiber BTU via a Mikrotik RB750G which splits the VLANs to 2 separate ports - my IPTV is happy...
  15. ekhoo

    Cabling - Long Runs - Individual runs vs. using a switch

    I would also prefer home runs but if the distance is large than probably you could have a remote switch connected via 2 or more 1Gbps links. Just deployed a 2 building network where switches are linked via fiber (220m apart) 2x1Gbps and internally, I've switches on each floor connected via...
See more
Top