Recent content by ___Lele___

  1. L

    WPA authentication fails when more than 32 devices are connected

    Thanks Merlin. I noticed that this happens also with WPA2 off. Basically the router cannot connect more than 32 devices on a single radio it seems, even if the traffic is low. Is this something I can change in the source of again closed source? Any way around it? thanks
  2. L

    WPA authentication fails when more than 32 devices are connected

    Hi I'm my Asus RT-AC3200 (380.59b1 firmware) for a local hotspot but I see that as soon as any of the 3 radios reaches 32 authorized clients it blocks any further WPA2-Personal connections even if the CPU is nearly idle and there is very little load on the network. Can anybody guide me on how...
  3. L

    [Beta] Asuswrt-Merlin 380.59 Beta 2 is available

    I will. I also narrowed it down to some interference with USB 3.0 which raises the noise floor a lot. in some cases even to -70dBm which is a lot. Did you try to play with the "Reducing USB 3.0 interference" option in the firmware? Mine is enabled by default buy I wonder if there are some side...
  4. L

    [Beta] Asuswrt-Merlin 380.59 Beta 2 is available

    unfortunately I need both.. I forced the channel width to 20 MHz in the GUI and it went a lot better (even if it was already at 20 MHz but in 20/40 MHz settings). Problem is that then I forced it to 40 MHz and it still ran fine. Then back to 20/40 and still fine. Doesn't seem to be anything...
  5. L

    [Beta] Asuswrt-Merlin 380.59 Beta 2 is available

    I'm seeing some frequent disconnects of the 2.4GHz, i.e. 1 every 30-90 seconds. Stats: Channel 1 Width: 20MHz SNR: ~25-30dB average Signal: ~ -35dBm average Mode b/g/n Basic rates 1,2,5.5,11 Mbps Other networks: -Channel 6 (20 MHz) -Channel 11 (2 networks, 20 MHz) no bluetooth, microwave...
  6. L

    [Beta] Asuswrt-Merlin 380.59 Beta 2 is available

    Working fine so far thanks. I'm also recompiling this for source and playing around with the web interface, just for the fun of it. When I "make" do I need to "clean" the project each time (takes forever!) or can I just clean the www module? Without any "clean" at all some files appear not to...
  7. L

    [BETA] Asuswrt-Merlin 380.59 Beta 1 is now available

    no change unfortunately. Looks like there is something wrong with netatalk. Can I disable the module so it is not compiled? If yes, what's the cleanest way of doing it? I don't need compatibility with Macs What system are you using for compiling the code? EDIT: Also testing with Ubuntu 14.04...
  8. L

    [BETA] Asuswrt-Merlin 380.59 Beta 1 is now available

    Hi, If I don't switch to source I can't "make". It seems it only contains "src" while the older folders contain the makefiles. root@ubuntu:~/asuswrt-merlin/release/src-rt-7.x.main# ls src root@ubuntu:~/asuswrt-merlin/release/src-rt-7.x.main# make rt-ac3200 make: *** No rule to make target...
  9. L

    [BETA] Asuswrt-Merlin 380.59 Beta 1 is now available

    Thanks RMerlin, that helped. I'm running root@debian:~/asuswrt-merlin/release/src-rt-7.x.main/src# make rt-ac3200 but unfortunately I still can't compile. It keeps crashing at netatalk, see below. I'm running from a fresh install of Debian following the instruction on Git. The DB headers are...
  10. L

    [BETA] Asuswrt-Merlin 380.59 Beta 1 is now available

    Hi sorry for the simple question but is there any thread specifically for building the latest source? I have already cloned the repo (3 times!) and followed the instructions here (https://github.com/RMerl/asuswrt-merlin/wiki/Compile-Firmware-from-source-using-Ubuntu) but they seem to stop at...
Back
Top