Recent content by arewhy

I'm onboard with renaming Tools to Sysinfo. It would also make sense to rename Network Map to Dashboard it would be a more accurate description but considering that Network Map is the default landing page it's not really a big deal

Right you are! I should have looked before I pointed you in that direction. It's probably just as well because the wireless log isn't working in the alpha. Although it might not have been an issue because the BE routers were already on the 37xx code.

This is a known issue with MLO capable routers. https://www.snbforums.com/threads/even-when-not-using-mlo-it-still-changes-some-stuff.94070/ There's an alpha version out that addresses the issue if you cannot wait for an updated firmware release...

I think you're on to something, my WAN connection type is Automatic IP.

Hi, I have the same router, with the same firmware and I have a WireGuard client configured. I do not experience the loss of internet connectivity for my LAN devices after rebooting. My WG client is connected to NordVPN 24/7. As to router configuration, I have separate SSIDs for the 2.4 and 5...

I had a similar issue with my Shield Pro with an RT-AX86U router and the solution was to toggle on "Allow low power channels" under the Shields General Settings/Network & Internet. It doesn't make sense because my Wifi signal was reasonably strong.

Hello folks, The VLAN Switch Control settings for the Default IoT network are not being applied to the RT-BE88U AiMesh router with Merlin or ASUS 3006.102_37xxx firmware. The issue was not present on the GT-AX 6000 with ASUS 3006.102_34810. I don’t know if the issue was introduced when ASUS...

Hi IRX, You are not alone; I am having a similar issue! Although in my case, I only experience the issue on the Default IoT network. I'm in the process of writing up my findings but before I posted them, I was going to perform a factory reset to see if the issue was reproducible. I was also...

@RMerlin thank you for steering me toward dmesg. It was helpful. When I put the actual share in the path, I was getting an "invalid argument" error. I assumed, incorrectly, that it was because I specified the share name because when I didn't enter it, I'd get the mount failed error. After trying...

Thanks for the quick reply @RMerlin, I did fact load the cifs.ko kernel module first and the Backupmon.sh script also loads the cifs.ko module. I confirmed the module was loaded via lsmod. It is an old Buffalo NAS with @Shonk modified that can no longer be updated so SMB 1.0 is what it is...

I upgraded my wireless router from a GT-AX11000 Wifi 6 router to an RT-BE88U Wifi 7 router because I wanted to leverage the SDN capabilities. I loaded Merlin’s firmware and performed a factory reset on the BE88U and configured from scratch. I installed ASUS’s firmware over Merlin’s firmware on...

@ZebMcKayhan, thank you for your reply! I think that I am ok with full ipv6 access between guest wifi and the LAN but I will consider it further and thanks to you, I've got an idea on where to apply the proper rules if I change my mind:)

Congratulations and Thank You Merlin! I cannot say that I've been along for the full ride, but I can say that when I bought the RT-AC88U in March 2016, my first ASUS router, it was because of the availability of your firmware! Prior to this, I had a D-Link DIR-825 that I purchased in 2010. It...

I decided to give YazFi a shot for the increased IP address and firewall granularity. Installed YazFi, enabled it for both 2.4 and 5 GN2. Internet Access-Y, One way to Guest-Y, Client Isolation-N. Everything appeared to be working well until I received a notification on my phone that my Solar...

Dirty upgrade from 386.4 to 386.5 B1 on all devices. Everything is rock solid 24 hours in. @RMerlin thanks for the fix to the DFS status on 5 GHz-2:) I didn't update my AC86Us, because it was reported here that the wireless drivers for that device have not been updated and the issue I was...