Recent content by BlueiPhone

Installed new alpha 3004.388.7_alpha1-g4c689dffeb --- no problems... Thank you

I normally do not test alpha releases but I jumped in and I am very happy with this release. Looking forward to the Beta. I have a WireGuard VPN running always and it is working great. I port forward IP4 addresses using the nat-start table and the firewall-start table with iptables rules I...

There is a app called "HINT Control" that I run on my iPhone and it allows much more control of the T-Modem. The App is Free. No need for scripts. You are correct this can't be done with the native T-Mobile App.

I have an Asus GT-AXE16000 running the current merlin firmware. I am connected to the internet using TMHI. Everyone in my family is very happy with this configuation. Need more details on your setup and maybe add a signature too..

Now that ASUS supports putting a MTU size on the VPN - WireGuard Client. When setting up a WireGuard VPN @ TorGuard using their Tools -> Config Generator I select Tunnel Type of “WireGuard”, the default MTU is 1390. I have found with TMHI using 1310 for the MTU works better than 1390. Anyone...

I have the same problem and the same router... 1. Nothing plugged into the usb ports. 2. unplugged the routner for 5 mins will boot into 3004.388.4 3. flash the router and I get the message to manually reboot the router 4. it comes back to 3004.388.4 5. I have cleared all the cache and rebooted...

Thank you for the info.... I will be happy to test..... Thank you for the great softwrae....

This is my log: Aug 22 14:06:35 rc_service: watchdog 2829:notify_rc stop_aae Aug 22 14:06:35 rc_service: watchdog 2829:notify_rc start_mastiff Aug 22 14:06:35 rc_service: waitting "stop_aae" via watchdog ... Aug 22 14:06:36 Mastiff: init Aug 22 14:06:55 rc_service: httpd 2820:notify_rc...

I did a SSH to the router the MTU is 1420 ASUSWRT-Merlin GT-AXE16000 3004.388.4_0 Mon Aug 21 19:34:19 UTC 2023 ClayNKuky@GT-AXE16000:/tmp/home/root# ifconfig wgc1 wgc1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.13.128.93...

Tks again for all your help... I did the command with the / and it accepted it... I am assuming that when I start the wgc1 it should process the command. I stopped the wgc1 and rebooted the router. When I start the wgc1 I see no difference... ClayNKuky@GT-AXE16000:/tmp/home/root# ifconfig...

I created the file with: nano /jffs/scripts/wgclient-start Then I pasted these two commands into the file #!/bin/sh ip link set dev wgc1 mtu 1376 Did a control-X to exit and saved the file When I do this command: chmod +x jffs/scripts/wgclient-start I get this...

I SSH to the router and looked at the MTU size. It was 1420... I adjusted it down to a MTU size of 1310 and now I it connects and does not hang... and the speed of the Wireguard VPN is great. Now I have to make it perm when the wgc comes on line. Any help with making it more permanent would be...

When TorGuard creates the config file that gets imported into the Router. It does set the MTU size. I am assuming that ASUS is not setting this. What is the SSH command to use to see what the current MTU on wgc1 size is berfore I change it? Thank you for your suggestions... Clay

Is there anyone who uses TMHI with WireGuard to TorGuard? TorGuard has a Windows App that I can connect to TorGuard using WireGuard. I set the service on TorGuard to Wireguard & I have to set the TorGuard’s Windows app MTU to 1376. It connects and works great. I would like to move my...

I am confused. I am running on a RT-AX88U and with firmware 384.18. I manage all my devices on my local network using DHCP on the RT-AX88U. I was adding my grandson’s laptop to the DHCP table and this message popped up. I thought I could have 128 devices in the table. I do have 64 devices in...