Menu
What's new
By:
Filters Better Search

Recent content by jpr105

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. jpr105

    My RT-AC68U is resuscitated!

    Hi, Here is what I've done : https://www.snbforums.com/threads/issue-accessing-my-rt-ac68u-using-php-and-ssh2.49355/#post-445720 Thanks for your answers. Regards
  2. jpr105

    Turning off wireless in Merlin

    If that can help : https://www.snbforums.com/threads/issue-accessing-my-rt-ac68u-using-php-and-ssh2.49355/#post-445720 Regards
  3. jpr105

    Issue accessing my RT-AC68U using PHP and SSH2

    Hi, Here is the PHP I use every days ... If that can help :) https://pastebin.com/iavFZM2X Regards - Jean-Paul PS : you need to have Libssh2 installed (https://libssh2.org/)
  4. jpr105

    Issue accessing my RT-AC68U using PHP and SSH2

    Thanks a lot @RMerlin and @ColinTaylor, I think I have everything I need to succeed in my project. I test and come back to post my solution if it can help someone else. Thanks again. Regards - Jean-Paul
  5. jpr105

    Issue accessing my RT-AC68U using PHP and SSH2

    Hello, To complete my last post, I noticed there was no synchronization between the action (wl -i eth1 radio on or wl -i eth1 radio off) and the Web GUI and I do not find this very "clean" :(. I found another method on this forum ... is it better? #get 2,4ghz radio status nvram get wl_radio...
  6. jpr105

    Issue accessing my RT-AC68U using PHP and SSH2

    You were right, the problem was on my side and it works now ... I can now connect to my router without problems :) The purpose of my PHP script is to turn ON or OFF, "on demand", my 2.4Ghz wifi signal. I tested these commands successfully: wl -i eth1 radio on wl -i eth1 radio off But before...
  7. jpr105

    Issue accessing my RT-AC68U using PHP and SSH2

    Hello, I need to access my RT-AC68U in SSH. So I configured the router as follows: Enable SSH = LAN Only Allow SSH Port Forwarding = Yes (not sure this is necessary) SSH port = 2222 Allow Password Login = Yes Enable SSH Brute Force Protection = Yes When I connect from my iMac or Raspberry...
    • jpr105
    • Thread
    • php radio ssh wifi
    • Replies: 7
    • Forum: Routers
  8. jpr105

    My RT-AC68U is resuscitated!

    Hi @Treadler , That's it, I finally found time to reconfigure my AC68U and you're right ... it's much more stable and it offers new possibilities. Thanks again. :) Another question now about scripts ... if you do not mind. I want to connect to the RT-AC68U (within my LAN network) from my home...
  9. jpr105

    My RT-AC68U is resuscitated!

    Thank you very much, I appreciate your help. But as I said before I will do it in July ... yet my mind is occupied with our next trip to Ireland. Between motorhome preparation and POIs selection with their GPS coordinates I have not much time. ;) Regards - Jean-Paul
  10. jpr105

    My RT-AC68U is resuscitated!

    Yes I did, with the initialize method and everything went OK. Next step : what do I have to do to be "Merlin ready" ?
  11. jpr105

    My RT-AC68U is resuscitated!

    Thank you for your answer. As there is no rush now, I think I'll switch to Merlin this summer. Regards - Jean-Paul
  12. jpr105

    My RT-AC68U is resuscitated!

    Hello, This is my first post on this forum and I ask your indulgence if I do not respect the rules in use on it. Here is my case: I have an Asus RT-AC68U that I wanted to flash last week to the last official release (3.0.0.4.384.20648) ... what a bad idea! After the application of the new...
See more
Top