Recent content by Livin

Hi Guys, I'm sure this is a simple answer but I cant find any specific info/docs on it, except CGPT so want to be sure it is correct... I have DHCP reservations for devices .2 to .99 (I aligned device types like cams, AV equip, mobile devices, Alexa, etc based on IP number). Most, not all, of...

guys, what 4G (LTE) devices work best with a GT-AX6000 and this script? I need something that will not use data (SIM service completely off/disconnected would be best, no keep alives since they often take up 1-2mb a day) when the device is not failed-to... I pay per MB for the backup SIM I'm...

the update check doesnt see .8 and forceupdate installs .7 I had to use the install command on the git site... /usr/sbin/curl -fsL --retry 3 "https://raw.githubusercontent.com/AMTM-OSR/YazDHCP/master/YazDHCP.sh" -o "/jffs/scripts/YazDHCP" && chmod 0755 /jffs/scripts/YazDHCP &&...

Thank you... I didnt know about this, been running 1.0.6. I'll update to .7 and try it again :)

easier said than done when you have 50+ devices... it will take me a long long time to add static to all of them.

Today I moved from GT-AX6000_3004.388.8_4 to GT-AX6000_3006_102.4_0 and then noticed all my DHCP reservations were gone. I tried to restore the config from backup (which I just took minutes before) and that didnt help. I reflashed 3004.388.8_4 and all was fine again. Is this a known issue and I...

I've tried custom port and port 22... says 'actively refused'

How do we setu the mesh node to accept SSH? My main Router uses a custom port for SSH (which works fine) but I dont see how to do it on the AImesh Node - I tried port 22 and the custom port I set on the main router, neither work. I have the latest Merlin on both. thanks for the help!

I dont know what you mean... where would I be checking such a thing - and what would it look like? For context, previously I had 3 separate ASUS routers, all sending syslogs to my central server... that worked just fine. I since changed to 2 routers using AImesh. I just weant the same end...

thanks, I'll check to see... both routers, and the receiving syslog server, are inside the LAN, no FW between anything. I have a script someone gave me that parses the log and matches MACs to entries for 'assoc' and 'dhcp'... I purely log devices that come on/off the network and when.

On the main AP node I set it under System Log - General Log but how do I set it on the remote mesh node? Searches only shows using Scribe; I dont want to do that. I do have Marlin installed on both main and remote nodes, thanks!

Wifi is on, I only turned of the 2.4g radio on the Node. No reason to have it on - it will only add to the interference. It did run overnight, and it was working immediately yesterday when first installed... running it over night was when it "broke"

Yesterday I installed fresh/new GT6000 (AP) + AX68U (node). It worked great, yesterday! Now I'm noticing that no clients connect to the node, even when 10 to 20 ft away through 1 interior wall. The AP is on the extreme end, of the house 2 floors down (same locations as my prior AC86Us; worked...

@L&LD update... GT-AX6000 & RT-AX68U up and running and so far, easily covering/replace all 3 of AC86Us. Interested in tweaks you suggest, should I be using AIMesh (AX68U is in AP mode right now)? Thoughts on house location/placement? thx, this looks like a nice upgrade

@L&LD where would you place the GT-AX6000 & RT-AX68U in my house? I've attached blueprints with #s at the locations I have wires to the cable modem (in basement under the stairs) for instance... AX6000 at #1 in the basement (under stair well - center of the main floor which is above it) + AX68U...