Recent content by matssa

Great thanks, and what should I add in the reverse DNS since I'm using unbound? Let it be since it won't be used?

Hey guys, I had to reinstall my router from scratch since the wifi was buggy. Therefore I'm doing Adguard from scratch with unbound. Unbound installed and I'm blocked at configuring the different DNS settings. For the upstream, here is my config. I added the lan configuration (local-domain...

Thanks for all your feedback. I tried using the GUI but it didn't work before. However, not sure what I made differently, I think I managed to make it work. From what I can imagine, the configuration of the bond on my NUC wasn't very good and after changing several stuff it now works. Thanks!

Hi everyone, I want to use Link aggregation between my NUC and my router. I enabled the bonding mode under debian on my NUC and specified mode 4, which should be the good type (802.3ad). I then linked two ethernet ports to the AX88U (ports 1 and 2) and then tried to enable this under the Asus...

Hey, Ok thanks not really sure that I needed that since they should use the private DNS settings right? In terms of AGH config, what do you suggest between the 3 settings (fastest IP, parallel demands or load balancing)? Other question, is this "better" than adding directly the redirections...

Hi, Yes, here is what I added in the dnsmasq.conf.add under /jffs/configs: interface=wg* # WireGuard address=/<redacted.something.something>/<redacted 192 IP>

Hey, Sorry for the late reply, heck here... I didn't change the default settings for AGH. Below are my DNS upstream : [/0.0.e.8.7.f.a.8.8.0.b.c.1.0.a.2.ip6.arpa/][::]:553 [/router.asus.com/][::]:553 [/www.asusnetwork.net/][::]:553 [/www.asusrouter.com/][::]:553...

Heya, Question on dnsmasq : I set some custom domain names inside so that my queries stays on my local network (for example test.com --> 192.168.X.X). Before AGH, no problem. Since I installed AGH they don't seem to work anymore, even though I didn't change any parameters (or than adding...

Ok so just checked and I configued Aghard home to be the router DNS stuff as well. Activated wireguard server and DNS stopped working for my home network. For me, the Wireguard server uses either the DNS entry for the router (mine is emtpy since I use adgard directly on the router), either the...

Hi, Thanks for the reply, didn't even know you could press advanced settings, when I clicked before it didn't want to switch... I also check the Asus stuff before and it isn't really that thorough. When checking the advanced stuff, you can't change the DNS server, it's by default the IPv4...

Hey guys, Before the latest update, I was using WIreguard directly on my router using the amtm addon (server on my router and client on my phone in order to use the home Adguard stuff and DNS and access to my NAS and all). With the latest version, we can (if I understood correctly), directly...

Hey guys, quick question, I hope you can help :) I'm using the wireguard from amtm on my Asus AX88u without any issues but in one case : a electrical black out. Indeed, I have my router behind my service provider router (I can't replace it with my AX88U), so after a blackout both routers boot...

Thanks for your quick answer! If I understand correctly: - Unbound replaces the Google or Cloudflared Dns provider in order to avoid DNS leak and maybe improve overall DNS response and stability - Adguard is a DNS filter and can be linked to the Ubound install instead of Google or Cloudflare...

Hey all, When installing the latest version there is a new option to run AGH as a local caching service. Since I'm going to use Unbound, what is the difference with this new option? Thanks!

Thanks for your help, managed to reset it. I saw this wiki but I didn't manage to find the .yaml file, found it on the USB flash drive under /etc/AdGuardHome....