Recent content by ninja888

Thanks - I’ll raise it with Asus although I guess it is likely they will want me to revert to the standard firmware to see if still an issue - meaning downtime as I don’t have a spare RT-AC86U to confirm this with. It would be useful to see whether others have this issue (whether or not AC86u...

Here is the brctl show output: admin@RT-AC86U:/tmp/home/root# brctl show bridge name bridge id STP enabled interfaces br0 8000.04d9f5927758 yes eth2 eth3...

How would I find the VLAN ID of IPTV? I checked the LAN->IPTV tab and this just indicates the Profile Name of “Unifi-Home”? here are the MAC addresses in the ifconfig output for brX and wlX.Y - As you can see br0 and br1 share the same MAC (which is different to br2) but all of the wlX.Y...

With “Enable VPN + DHCP Connection” set to No (and router rebooted), the 2.4Ghz Guest1 network wl0.1 appears to be connected to the br1 bridge but the br1 bridge still has an IP range of 169.254.0.0 and all 2.4Ghz Guest 1 clients are not given a DHCP IP address when connecting and therefore...

My WAN connection is PPPoE and I have to enable an ISP IPTV profile for the connection to work (even though I don’t actually use the IPTV). So it appears that the issue is caused by wl0.1 not being attached to br1 (192.168.101.0/24)? Is that something the Asus Merlin devs could take a look at...

I did some investigation into this same issue in another post - Definately looks like a bug somewhere? Post in thread 'Guest Network not working in Firmware 386.2_2' http://www.snbforums.com/threads/guest-network-not-working-in-firmware-386-2_2.71981/post-724432

So I did a little more digging here and something definitely doesn’t look right with the 2.4Ghz Guest Network 1 interface (wl0.1) / br1 when “Access Intranet” is set to “Disable” - In this scenario, the wl0.1 interface is not attached to any bridge and all 2.4Ghz Guest 1 clients cannot access...

I assume this is still a bug since I’m on the latest firmware with AC86 master router and AX56U node and see the following. Note: I also have OpenVPN client configured on the Master node… (A) 2.4ghz guest #1 does not work - Master and AiMesh node clients do not get a valid DHCP address and...

I’m seeing the same type of issue with my multiple RP-AC55 units rebooting themselves. Although I have both Linux and Windows clients on the network, are you sure the issue is related to Linux hosts? My RP-AC55 units seem to reboot more (sometimes like 3-4 times in an hour) when there’s video...

When changing routers (different Asus models), I usually manually configure the new router from the old's settings in the Web GUI. There doesn't seem to be a way currently to mass configure the DHCP Manual Addresses (LAN -> DHCP Server -> Manually Assigned IPs) and Port Forwarding (WAN ->...

I assume this is still an issue since the SNMP tab is not present in the RT-AC86U Web GUI? Has this been tested recently with net-snmp and has the issue been raised with net-snmp? Thanks!

Yes, I will disable link aggregation and just use the first 4 LAN Ports to see if that makes any difference but it would still be good to know if anyone has any suggestions for userspace commands which can be run over local SSH (WiFi) to disable/enable the ports in case this happens again -...

Ok thanks Colin... If there’s no userspace command to view the reliable states of the ports across both switches, are you aware of any command which can reliably disable / reenable the interfaces / ports / switches to mimic a physical replugging of each of the cables? This would at least in...

Intriguing! If robocfg can't be trusted to output the correct config for both the Broadcom (Ports 1-4 and WAN?) and Realtek (Port 5 -8 ) switches, is here a command line command that can be trusted and allows the user to disable / re-enable the switches/ports individually to mimic physical...

Hi Guys, I’m seeing a very strange problem with my Asus RT-AC88U (at the time running Merlin 384.10_2 but I’ve since upgraded firmware to 384.11 Beta 1) where, randomly (it happened about 4 times in the last couple of weeks) , the router will lose WAN connection (WAN light on router is RED) and...