Recent content by pncu

Hi, I have the 105 AIO for n66u and everything is great. Just 1 question about using transmission. So when I want to use transmission to dl a torrent, I have to download the tracker onto my computer, then open transmission web gui, then open the folder then load the tracker? Is there a...

It shows closed but I can still download so I'll figure that out later. I have my disk to spin down after idle for 15mins. After my disk spins down and spins back up, transmission web interface doesn't work. I can get to the page but the middle where it should be blank has writing on it like...

I think the first way is right and thats the way I did it. My port is still showing closed.

the one i'm using is 32bit. Thanks for your input. I reformatted and its partly working. Some folders I can write into some folders I can't. I'll figure it out later I guess.

nvm got it working. One other question, even though I did the firewall-start my port is still showing closed. so for firewall configuration, I put in "nano -w /jffs/scripts/firewall-start" then a page like the settings config page comes up so I put in #!/bin/sh iptables -I INPUT -p tcp...

I was on .24 then reverted to .23b to make sure it wasn't the firmware. So I can assume everyone else using ext3 can write to it through the router's usb and this is just me?

I have a Rt-n66u that is running on Merlin's firmware. I've been using a 2tb seagate goflex drive formatted to ntfs connected to the usb slot as my NAS which was decent. I wanted to install Transmission on it so I could dl stuff overnight with comp turned off but...

ok so I deleted tons of old stuff I'll never need again and I formatted my 2tb goflex drive to ext3 using gparted. Then I had to use ext2volume manager to be able to see the ext3 drive on my windows 7. Then I moved about a 800gigs of data back onto it overnight. Plugged into windows, I can...

I updated to .24 from .23b this morning. Everything seems to be working ok but for me at least, I cannot access my usb drive. Right after update, I could access my drive but I could not write onto it. It kept saying I needed permission. I tried to reboot, and after the reboot, I cannot access...

So, if I have a usb flash drive on sda1 and hdd on sdb1 I adjust the commands accordingly? when installing entware/optware, I'd install adjust the commands being put into Putty as sda1 and when installing the Transmission, I'd adjust the directories to sdb1 but leave the rest to sda1 so...

Thanks, I guess that means on Tomato, entware/optware or Transmssion is installed somewhere on the router but in this case, I am installing it on the HDD? So, if I switch the HDD to a different one after I've installed Transmission, does that mean it is gone and I have to do this process over...

is there any way to do it without ext2/3? The drive I'm using is formatted ntfs with over a terabyte of data on it so I can't format the drive as I'd lose all that data. Is there any way to do it without ext2/3? I used tomato for a couple days and it had Transmission on it and I was...

Thanks. I've read both your's and TeHashX's guide on installing transmission. I have a 2TB drive formatted to ntfs and it has about 1.3TB of data in it already so formatting it isn't an option as all my drives combined isn't enough to store the data temporarily while it's being formatted...

Is it possible to install something like transmission for torrents on Merlin build? Download Master never lets my HDD spin down but on Tomato, the using transmission to dl, my drive still spun down when idle.

whats the difference between AIO BT-VPN MEGA-VPN TOR-VPN AND VPN? I also see the changelog is different from the post above missing the last line about the USB. Was that something that could have fixed my 2MB/s wired write speed?