Recent content by The Cool Dude

Hello again. Just an update since December 2023..... As of today March 2024 I have not heard anything back from Asus. I'm not holding my breath. I've also not changed anything in my network as everything is currently working fine. For clarity, my two RT-AX92U routers are both hard wired with...

Hi Everyone. Thanks for your thoughts.... I've reached out to Asus Support via the feedback section. No response yet. Since I've rolled back my firmware to 3.0.0.4.386_47468 everything has been solid. I never enabled the Ethernet Backhaul Mode in AiMesh/System Settings. It's always detected...

Hey guys. Just a heads up there is a problem with this firmware, at least if you are running with nodes. See my post here: https://www.snbforums.com/threads/aimesh-nodes-intermittently-disconnect-and-then-reconnect-at-random.87877/#post-878997 Hopefully they will have another release to fix...

Thought as much. Good call. Thanks again!

Hello everyone and thanks for all the replies and suggestions. Looks like Brad was correct. I downgraded my RX-AX89X from ASUS RT-AX89X Firmware version 3.0.0.4.388_32407 to 3.0.0.4.386_47468 and now my two RT-AX92U routers set as my nodes are showing up just fine again. Thanks again...

Hello again and thanks for the responses. Here is some more info that may help. Since I have reset to factory defaults, Ethernet Backhaul Mode is still disabled. I never had it enabled before the reset either. WPS is currently enabled. WIFI settings are all currently at default. I was using a...

Hello everyone. Hopefully someone can help shed some light on this weird issue. I have a RX-AX89X connected directly to my cable modem in the basement. I have two RT-AX92U routers set as my nodes. One on the main floor and on on the second floor. They are both hard wired with CAT6 Ethernet...

Thanks! I used a combination of NetSpot and inSSIDer to check things out. Also factory reset both devices with the reset button at the bottom. The WPS button method to reset them does nothing. To reset you need to use the reset button in the pinhole at the bottom. Unfortunately none of this...

Hi there. Sorry but I can't even get any better than 100 Mbps down using wireless on my XT8 and I have a 1G internet connection. Wired connection maxes out at around 500 Mbps. I got my pair of XT8s about a week ago through Amazon and have been fighting with this all week. I've tried a lot of...

Hello everyone. RT-AC87U x 2 Just updated from 384.5 to 384.9 dirty flash. No issues. Thank you RMerlin!

Thanks Merlin. Then from what you have said, the Ethernet Port Chart should be visible as I have many active clients. I use Edge as my browser. In the console I have a repeating message that says: SCRIPT7016: Use of XMLHttpRequest with the synchronous flag set to true is deprecated due to its...

Thanks Merlin. I don't understand. I have my 2nd router connected to an Ethernet port of my first router. Isn't that a client? I have many devices connected wired and wirelessly behind both routers. Surely one of them would be classified as I client. The Ethernet Port chart was visible until...

Hello there. Just flashed from 380.68 to 380.68_2 on my 2 RT-AC87U routers. My main router is in Wireless router mode (Default). The 2nd router is in Access Point(AP) mode. I just noticed something that I didn't really notice before. On my main router, after I have configured some Manually...

Thanks Makaveli! I'll try it out. Appreciate your response.

Hello. Thanks again to Merlin for another great release. On my 2 X RT-AC87U routers I upgraded from 380.67 to 380.68 about 8 hours ago. Everything seems OK except I've been noticing that in my system log it is getting flooded with DHCP entries like this: Aug 20 13:03:25 dnsmasq-dhcp[482]...