Moan
Occasional Visitor
Hi guys. I got a new Asus ROG Rapture GT-AX6000 router. My network is the following:
GT-AX6000:
QNAP QSW-1105-5T:
I noticed, that I can't get the full speed of 2.5Gb/s on My PC when I'm copying files from the Old NAS, New NAS and doing a speedtest at the same time. It maxes at ~1.6Gb/s, and either slows down the transfer of one of the NASes, or doesn't give the full speed on speedtest.
After trying dozens of different things, I noticed that the problem starts when I power cycle the QNAP QSW-1105-5T switch (unplug / plug the power). Then, data transfer from the New NAS to My PC goes by the GT-AX6000 router, instead of directly from the Switch.
Router restarts, PC restarts, multiple switch restarts, or executing ethctl eth5 phy-power down in Router SSH doesn't fix this issue.
I only managed to fix it by rebooting the New NAS. So after I reboot the new NAS, I am getting the full speed of 2.5Gb/s on my PC. Unplugging the New NAS ethernet for 1 minute doesn't fix this issue - only the full reboot.
Then, after the switch power cycle, after some GT-AX6000 reboot, or after some time - the bug starts occurring again, and the transfer from NAS 2 always goes by the router instead of Switch -> PC.
This was not happening on my old (bad) router: Xiaomi AX6000 with 2.5Gb/s LAN port.
I'm really confused and I don't know how to test it. Is it possible that it's some bug in the firmware? I'm using the newest Merlin: 388.2_2_rog.
I would very appreciate any help.
GT-AX6000:
- WAN: 1Gb/s download / 100Mb/s upload
- eth2: Old NAS (1Gb/s)
- eth5: Unmanaged QNAP QSW-1105-5T switch (2.5Gb/s)
QNAP QSW-1105-5T:
- eth1: GT-AX6000 (2.5Gb/s)
- eth2: New NAS (2.5Gb/s)
- eth3: My PC (2.5Gb/s)
I noticed, that I can't get the full speed of 2.5Gb/s on My PC when I'm copying files from the Old NAS, New NAS and doing a speedtest at the same time. It maxes at ~1.6Gb/s, and either slows down the transfer of one of the NASes, or doesn't give the full speed on speedtest.
After trying dozens of different things, I noticed that the problem starts when I power cycle the QNAP QSW-1105-5T switch (unplug / plug the power). Then, data transfer from the New NAS to My PC goes by the GT-AX6000 router, instead of directly from the Switch.
Router restarts, PC restarts, multiple switch restarts, or executing ethctl eth5 phy-power down in Router SSH doesn't fix this issue.
I only managed to fix it by rebooting the New NAS. So after I reboot the new NAS, I am getting the full speed of 2.5Gb/s on my PC. Unplugging the New NAS ethernet for 1 minute doesn't fix this issue - only the full reboot.
Then, after the switch power cycle, after some GT-AX6000 reboot, or after some time - the bug starts occurring again, and the transfer from NAS 2 always goes by the router instead of Switch -> PC.
This was not happening on my old (bad) router: Xiaomi AX6000 with 2.5Gb/s LAN port.
I'm really confused and I don't know how to test it. Is it possible that it's some bug in the firmware? I'm using the newest Merlin: 388.2_2_rog.
I would very appreciate any help.