Menu
What's new
By:
Filters Better Search

Recent content by aznphatb0i

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

  1. A

    Best way to configure 2 public IPs on ERLite-3?

    This was the information that was provided by my ISP: "Your request for IP information for your account is provided below. Along with your .XX2 you currently also have .XX3 through .XX6 to use The below is for order id - X-XXXXXXXXX Address: XX.XX.XXX.XX1 Netmask: 255.255.255.248= 29...
  2. A

    Best way to configure 2 public IPs on ERLite-3?

    I just got my NanoHD and am ready to start configuring this. Does anyone have any ideal guide to follow?
  3. A

    Comprehensive & up to date UniFi AP comparison chart? What's best for me?

    As a frame of reference, the speeds we are getting now from all employees using the DIR-890L is sufficient. See this thread: https://www.snbforums.com/threads/best-way-to-configure-2-public-ips-on-erlite-3.46620/ - my plan is to have the Guest AP have a separate public IP. I would move one of...
  4. A

    Comprehensive & up to date UniFi AP comparison chart? What's best for me?

    Hello! I hoped that the description of my current set-up would give a reference point. The DIR-890/L + TP-Link Archer is "acceptable." The TP-Link network is a "test network" that has devices on it and we purposely unplug the AP during some tests. The DIR-890/L is the "primary" network with...
  5. A

    Comprehensive & up to date UniFi AP comparison chart? What's best for me?

    Hello! I currently use an ERLite3 + EdgeSwitch Lite with a DIR-890/L as the primary WiFi AP and a TP-Link Archer as a secondary AP. I am doing some upgrades and am considering switching to the UAP-nanoHD for my primary AP. Is this the best choice for me? I can't seem to find a comprehensive...
  6. A

    Best way to configure 2 public IPs on ERLite-3?

    Hello! I currently have an ERLite-3 with CogentCo internet and a single static public IP. I want to use 2 public IP addresses, and have one assigned to each LAN port on the ERLite-3. Is this possible and what is the easiest / best way to go about this? Are there any negatives to this...
  7. A

    Simplest client(s) to site VPN solution on ERLite‑3?

    Thank you for the reply! Do you have any recommended solutions / set-up guides for a simple L2TP/IPSEC configuration? I take it that there is no reason to use OpenVPN or SoftEther for my basic use case?
  8. A

    Simplest client(s) to site VPN solution on ERLite‑3?

    Hey fellas! 1. My office internet is powered by an ERLite-3 2. There are a couple of devices on my LAN that can only be accessed via local IP (think Android ADB) 3. I would like to allow 2-3 remote users who live geographically far away to access the office local network so they can access...
  9. A

    Lowest cost Cisco managed switch with Spanning Tree Protocol and Portfast

    Hello everyone! I hope someone might have some advice for me here; I have a miniPC device which apparently has an issue getting an IP when connected to a Cisco managed switch that is doing spanning tree protocol and has portfast disabled. I want to replicate the issue locally, so am looking...
  10. A

    Please give me feedback on my network setup

    Hi all you small net builders! I hope you can give me your 2c on my network and if there's anything tips or improvements. • Cat6 is used for every connection • The distance between any of the switches/routers doesn't exceed a few feet of cable • The R7000 in AP mode is soon going to be...
  11. A

    How to install and run Iperf on Ubiquiti Edgerouter Lite?

    Hey guys! I have an EdgeRouter Lite and would like to install and run Iperf (https://iperf.fr/) on it. I read that it's possible to install and run Debian packages like Iperf on the Eddgerouter Lite, but I am very new to the Edgerouter Lite and am unable to find the functionality. I read over...
  12. A

    How to allow ICMP ping on EdgeRouter Lite?

    Hey guys! I have an EdgeRouter Lite serving our small office, we use Cogent as our ISP. To proactively monitor our circuit, I need to allow ICMP ping of our network. I configured the EdgeRouter using the first config from here...
See more
Top