Recent content by josh3003

  • ATTENTION! As of November 1, 2020, you are not able to reply to threads 6 months after the thread is opened if there are more than 500 posts in the thread.
    Threads will not be locked, so posts may still be edited by their authors.
    Just start a new thread on the topic to post if you get an error message when trying to reply to a thread.
  1. J

    RT-AC68U temp throttle limit

    Yeah its sitting in the low to mid 90s. What should I look at cooling wise?
  2. J

    RT-AC68U temp throttle limit

    Hi all just a quick question. I sit my router ontop of my PC which runs 24/7 at the moment and is quite toasty. At what point should I look at installing a fan behind the back of the router? Just want to know at what limit the cpu will begin to throttle roughly. Thanks.
  3. J

    RT AC68U login page not loading.

    Can't say I've had the issue since going to 386+ However, it has only been a month and the timeouts have usually been rare. But safe to say so far it looks pretty stable.
  4. J

    RT AC68U login page not loading.

    I've done that in the past, I've updated now to 386.1 so I'll keep an eye on things.
  5. J

    RT AC68U login page not loading.

    Every few days I've noticed my router login page times out and doesn't load. I have turned off the periodic check for trend micro updates/installs and run a cronjob every day at 4am to restart httpd service. I have to physically power cycle my router to get the login screen to show. Any ideas...
  6. J

    QoS - WAN/LAN Bandwidth monitor not working

    Yeah does exactly that, rather than setting a download limit on the device, I can set it through the router. So that solves the problem. I'll just leave it as fq_codel. Seems pretty rock solid tbh.
  7. J

    QoS - WAN/LAN Bandwidth monitor not working

    Yeah that makes sense. Is fq_codel still the best queue discipline? Also for bandwidth limiter can I just have the devices that I want to be specifically limited and the ones that have not been added are fine to use as much or as little bandwidth as needed?
  8. J

    QoS - WAN/LAN Bandwidth monitor not working

    Too easy, so for the AC68u, is FlexQoS the new one I should look at? I am on a 100down/20up connection currently.
  9. J

    QoS - WAN/LAN Bandwidth monitor not working

    Are these the kind of issues? For instance when I am downloading on a device (lowest priority) I have to actually throttle the download limit to not saturate my connection. Then, when I run for instance, a speedtest on my highest priority device (My PC) it seems that the device which was doing...
  10. J

    QoS - WAN/LAN Bandwidth monitor not working

    Does QoS - WAN/LAN bandwidth page not work correctly if QOS itself is not enabled on the second tab? Under the http://192.168.1.1/AdaptiveQoS_Bandwidth_Monitor.asp page? I tried setting my PC to have the highest bandwidth and others as the lowest however it seems that there is no real priority...
  11. J

    Traffic Analyzer crashing httpd

    A At least now my httpd service should be staying alive I'll be able to. Before I knew about restarting that service I rebooted the router which of course killed the logs. I'll keep an eye on them.
  12. J

    Release [Fork] Asuswrt-Merlin 374 LTS release 45EC

    Yeah thanks @ColinTaylor is right I sorted it out in the end. On Merlin, it turns out the strict-order actually flips the WAN DNS around, so DNS2 is actually DNS1 and vice versa.
  13. J

    Traffic Analyzer crashing httpd

    Highly doubt it as it has never froze for months after I turned off traffic analyser - statistics. It'll be fine now that I sorted the cronjob out. A daily service restart is all I'll need for it to function as it probably only happened maybe once a fortnight.
  14. J

    Traffic Analyzer crashing httpd

    Sorted it out. Tested with a 2 minute cronjob to reset httpd which it did. Just going to stick with a daily 4am reset. Awesome, I'm going to enable traffic analyser after the reboot.
Top