What's new
By:

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by kakashisensei

  1. K

    AX3000v2 cant find lan port ids in cli

    These are my results with ethtool. Returns no data for eth2 and eht3. For eth1, its 2500mbps, but this router doesn't have 2.5gb ports. Even when I did ethctl eth1 phy-power down, it didnt do anything. Lan ports, wifi still work. Nothing shows up in syslog. This router just seems different...
  2. K

    AX3000v2 cant find lan port ids in cli

    I am running gnuton fork of asusmerlin on my AX3000v2 (AX58v2) in AP mode with AI mesh nodes attached. I have an issue where one lan port degrades from 1gb to 100mb randomly. I can't change the wire or other stuff that might be causing it. I rather just have a script monitor it and reset the...
  3. K

    Ethctl for lan port? Can't find interface name

    I have an ax3000 v2 that isn't supported by asusmerlin. I have an issue where one of the lan ports keeps dropping from 1gbps to 100mbps randomly. I have to either reboot the router or replug the cable. Its good for a while before it drops again. Not sure if its cable, switch, or passive poe...
  4. K

    Can an aimesh node be main switch connected to the isp router (not the aimesh main AP/node)?

    I am using the latest official firmwares for both devices. I get 160mhz dfs when I am connected to AX AP, and i get 80mhz dfs when I roam to the AC68U. At least thats what my ubuquiti scanning app is showing. Can confirm I get like 80-100MB/s to my NAS at 160mhz.
  5. K

    Can an aimesh node be main switch connected to the isp router (not the aimesh main AP/node)?

    I currently have an edgerouter X as my router wtih 1gig fiber. Using an AX58U as the main AP/node and an AC68U as a mesh node. The AX58U is connected to the edgerouter and is the main switch for my entire LAN traffic. I am thinking it would be better to move my AX58U to another location for...
  6. K

    RT-AC68U aimesh node dropped connections/ latency spikes with firmware 384.81049 and later

    Havent checked this thread back until now. Glad to hear some people have reported good results with 384.13. Fyi both my ac68u routers are the tmobile one converted to ac68u. I have configured the jfss partition correctly i think. Been running on 384.13 for the node and its been great. 384.19 on...
  7. K

    RT-AC68U aimesh node dropped connections/ latency spikes with firmware 384.81049 and later

    I have two ac68u routers and have been using them in aimesh ever since merlin added this to his releases. I've been updating both the router and node sporadically with the latest merlin firmware over the last year. They were working fine until about a few months ago. Any device connected (wired...
  8. K

    WNDR3700 more 5ghz throughput than e2000?

    I have a refurb e2000 running dd-wrt and using it as 802.11n 5ghz @ 40mhz. The specs say it has 2 tx/rx antennas and 1 rx antenna. Testing using my laptop, using a bigfoot 1102 wifi (max 2 antennas), I can transfer at an avg rate of 92 Mbps to my nas. But when sending a file to my laptop...
See more
Back
Top
✖