Recent content by Kenji

Hello everyone, Thank you for the feedback. I have now managed to get everything up and running. I installed Headscale using the helper script on a Proxmox server in my LAN (where I’m also running Pi-hole). So far, I’ve only been able to access the interface (UI) via the internal IP address —...

Hello everyone, I’m currently trying to configure Tailscale so that it runs via a Headscale server. I added the following under Operation Mode “Custom” (O), point 4: --reset --login-server=https://headscale.8x9.synology.me --auth-key=hskey-auth-PDxxxte --advertise-exit-node...

Hello everyone, I use Tailmon on my Asus router and it works very well. This is connected to the Fritzbox via an access point. Now I access my LAN externally with my mobile phone as an exit note (asus router) and that works. by the way, I also use a pihole that filters out everything. Now my...

Router is: RT-AX86U Firmware version is: 388.1 Blocklists used are: some, about 1.5 million entries Other user scripts ran are: see appendices. Total router memory usage percentage is: see appendices. Enclosed is the information. Under Diversion, I had the same block lists and about 1.8...

Hi all, I have a few questions regarding Adguard. I have been using it for a relatively long time but have a few criticisms: - Unblocking individual requests that are in a block list ends up with very long loading times because Adguard is not accessible. This can only be resolved by restarting...

Hello colleagues, I have been testing Adguard on my RT-AC86U for a little while now. Unfortunately, I found out quite early on that the speed of the DNS resolution and the speed of the web interface was very slow. I tested this with very little DNS blacklists and with a lot. Unfortunately, the...

So now Adguard works so far on the router after DNSCrypt was disabled. I have now noticed that only simple DNS queries are in the connection log. I assumed that I simply activate a checkbox and the connection is then transmitted encrypted. (Similar to DNYCrypt over amtm) Can it be that this...

Hello, can someone help me fix this error? So quite I do not know who should listen on this port. [fatal] couldn't start forwarding DNS server: listening to udp socket: listen udp 0.0.0.0:53: bind: address already in use Is it possible that this is related to the VPN server (UDP)? Thanks a lot

Thank you very much for the answers. I have now tested a bit and it now seems to work. I have disabled the daily reboot of the Asus. This had been activated every morning by me. Furthermore, I had probably out of ignorance in the Fritzbox DNS rebind protection activated with the Ip of the...

I have already tried that. Unfortunately, that did not help. In the course of time I have also reset the router to default, unfortunately that did not help either :$

Hello together, I need your help. I have been using an AC86U with amtm etc for a long time and everything works as it should. Now I have for the 30th time Skynet installed to hope for additional benefits through security. Unfortunately, I was always disappointed and in the end I had to...

thank's for the Tipps. I have now done this with the backup and the router ran without problems for 3 days. Now I had to restart it via the web interface. Now I have the problem that the swapfile is no longer found .. despite being correctly mounted, amtm does not find the swapfile. the USB...

I may have a stupid question .. is it possible to move amtm with all scripts? I have two usb sticks with 2 partitions each. USB 1 (partion swap file + partions empty), USB 2 (partion amtm + partion empty). I would like to move the USB 1 to the empty partition that is already pre-matematized. I...

Hello, I have freshly configured my router. Unfortunately I cannot get uiDivStats installed. The last point remains. The statistics are therefore not visible in the interface.

okay, after restarting a router I suddenly had the same error. I tried to uninstall dnscrypt via Putty but after entering "di" it stopped after 3 lines. After another 5 restarts it worked again at some point. So despite fallback_resolver the connection did not work. -- Jun 13 18:36:37 lul...