routing rules

I have the following configuration / setup on my router: Setup 1x OpenVPN client via user Merlin user interface Setup 5x Wireguard VPN clients via the Merlin user interface Router setup as an exit node for Tailscale (via tailmon) Use VPN director to route Tailscale IPv4s into VPN tunnels with...

Hello all, This is my first post in here. I try to connect only one device in my network to access internet over OpenVPN client (tun15 interface in my case). I do it on Asus RT-AX53U router with ASUSWRT (Operation Mode:Wireless router Firmware Version:3.0.0.4.386_68691) by uploading .ovpn...

Hi to everybody! I've two FTTH Lines connected to my RT-AC86U: - Line1 (1Gbit/300Mbit) set as primary, Wan (PPOE) direct connected to the ISP's Ont - Line2 (1Gbit/1Gbit) set ad secondary, Lan connected to a FritzBox! Router (connected to the secondary ISP's Ont) I would have liked to use dual...

Hi to everybody! I've two FTTH Lines connected to my RT-AC86U: - Line1 (1Gbit/300Mbit) set as primary, Wan (PPOE) direct connected to the ISP's Ont - Line2 (1Gbit/1Gbit) set ad secondary, Lan connected to a FritzBox! Router (connected to the secondary ISP's Ont) I've some problem using dual Wan...

I have an AC68P running merlin 386.3_2 firmware. WAN port is hooked up to a modem, whose IP address is 192.168.1.1. Router's IP is 192.168.3.1/Subnet Mask 255.255.255.0. I have OpenVPN servers running on ports 1194 and 443, Client will use VPN to access - Both. VPN Subnet / Netmask are...

Hello! I am happy that I have found that forum. Lately I was annoyed too much with the StackExchange sites. I really don't understand why people there are so unfriendly. Especially the ones with high ranking, they tend to have authority issues. I have the following network topology as on the...

Hi I'm building a multi point VPN system with Wireguard, and hoping some here could help with the config. The start point is: I have three location all with 172.16.X.X / 24 subnet lan and Raspberry 3 with Wireguard and Pi-Hole installed. All network have DDNS names. Setup is this: Network #1...

Not really sure how to describe this. I've been away for a couple of weeks, so nothing that I can think could/would have changed and I'm certain it was working. I have an AC68U as my primary gateway with a LAN IP of 192.168.1.1. DHCP is on, but I have a few statically assigned addresses for...

I am really stumped on this one. I have been having a heck of a time trying to figure out why I can't ping other computers on a client's network, while I am actively using a VPN connection into my server. This is a Client <-> Client scenario: Client/Network A 192.168.40.0 <---> Internet <--->...

I have an Asus RT-AC86U running the latest Merlin firmware. I have an openvpn client setup. Currently all traffic goes over the VPN. However, my goal is that wireless clients that connect to the guess WiFi are not routed through the VPN tunnel. Is there a policy based routing rule that will do...

Hi, Here's my scenario: My kit is an ASUS RT-AC5300 running Merlin 384.6 firmware with a second AC5300 working as a hard wired AP. I have terrible UPLOAD on my home broadband. I mean TERRIBLE. It is on average 0.4Mbps! My download on home broadband is 12-18Mbps. I've spoken to everyone and...

Trying to set up an AC68U running latest stock firmware for dual WAN with load balancing. The manual and FAQs available from ASUS provide no information about setting up routing rules. I have scoured the web and the information is confusing and often in conflict. I want to clarify a few...

My goal is to be able to connect to private LAN (192.168.1.0/24) via Ubuntu VPS. For example I want this forwarding: http://{Ubuntu WAN IP}:443 --> http://{Private LAN IP}:443 Please take a look at attached screenshots. As I understand the problem is in inability to communicate between two...

Hi, I am using my AC3200 running latest 384.4 beta as as secondary router. In router mode so I can use goodies like guest network, IPv6 tunnel broker and OpenVPN server not available in access point mode. Here is my topology: Fios router to Internet, 192,168.0.1/24, does DHCP. AC3200 connected...

Hello there, Before I begin explaining my issue I want tot thank every active member who is trying to help other users (specially Merlin). I'm facing an issue with Dual WAN loading balance feature in my RT-AC88u router, running Merlin firmware. Whats I'm trying to achieve, my physical...